How to change the temperature on the alarm STARLINE A91 - author

Starline A91 Dialog - Instructions in Russian

How to change the temperature on the alarm STARLINE A91

Installation of car alarms should be made by qualified specialists. Car alarm is a complex technical device involving the connection to the electrical circuits of the car associated with the engine operation.

We strongly recommend wearing a key chain from car alarm on one bundle with the keys from the car.

If an icon warns about the discharge of the battery that warns the keychain on the display, take steps to replace the battery. We recommend to store a new spare battery in the car, keeping its factory packaging.

Read carefully this instruction and pay special attention to the sections marked with the sign. (!) .

Mandatory security measures when using the engine start function

It must be remembered that the car is a means of increased danger. Section 12.8. The rules of the road says: "The driver can leave his place or leave the vehicle if they are taken by the necessary measures that exclude spontaneous movement of the vehicle or using it in the absence of a driver."

Before operating a car alarm Starline A91, dialogue carefully read the measures of safe use of the function of the remote or automatic engine launch outlined below.

  1. Always park a car on an open, well-ventilated area.
  2. Always put the car on the parking brake, which should be in good condition and eliminate the possibility of moving the car.
  3. Leaving the car, be sure to install the control lever of the automatic transmission in the PARK position, and the shift lever of the manual gearbox - to the neutral position.
  4. If a manual transmission is used in your car, before turning on the function of the remote or automatic engine start, be sure to prepare the process for starting the engine - "software neutral".
  5. Never run the car engine in the absence of a driver if anyone is in front of the car or behind it.
  6. Never transmit car alarm management tracks to children, as well as other persons without their preliminary familiarization with this Instruction.
  7. On cars with a manual gearbox, it is not recommended to be remote or automatic starting the engine if the car is outside the visibility zone, and the auto alarm user is not able to control the engine start process.
  8. Before you include the remote or automatic engine start function:
  • Make sure in good condition of the car;
  • make sure there is enough fuel, oil, coolant, etc.;
  • Set the operating parameters of the salon heater (air conditioner), glass heating and other accessories for the required levels;
  • Install a regulator of blowing a salon on air circulation, which will make it possible to warm more efficiently or cool the air in the car.

Introduction

A source: http://mobilradio.ru/information/manuals/starline-a91-dialog.htm

Page Starline A91.

How to change the temperature on the alarm STARLINE A91

:

  • General Alarm Requirements
  • Characteristic Alarm Starline A91
  • Information about safety and technical specifications
  • Important Alarm Functions Starline A91
  • Starline A91 Alarm Supply Complete
  • Description Alarm Alarm A91 Challenge
  • Setting up the comfort modes Starine A91
  • Starline A91 Alarm Autorption Setup
  • Setting the STARLINE A91 signaling turbotimer

General description of alarm

STARLINE A91 Dialog Alarm is a modern automotive security system with a "fast dialog" radio control system and a motor autorun function. "Fast dialogue" - the control code with individual encryption keys eliminates the intelligent electronic hacking.

She is a representative of the producer budget family. Despite this, the inter-rubber connection is carried out in 8 channels from the transmitter transceiver. The security of a dialog sample, the floating channel method and a 128-bit code correspond to security. Each time you send a signal to a key chain or vice versa, the anti-theft system Starline produces an automatic choice of alternative frequency.

Despite the narrow spectrum of transceiver transmission and the extinct selection of the selective type signal, the A91 developers have worked with the radio chain of the A91 connection with the main unit. The solution of such a level, known under the technical term "method of expanding the spectrum with a jump-like perestroika frequency," is used for the first time in the world in the system of signaling control system and is a very significant complication of any attempts to hack code.

Starline anti-theft system The A91 model provides for the installation process on any cars. We receive a fiscal option, a very reliable, simple and universal security system.

Here you can see either download instructions

STARLINE A91 security functions

  1. Silent security mode, as well as a sound signal mode;
  2. option automatically turn on the security system;
  3. inclusion of protection without the use of keyfob and with a working engine;
  4. the product of automatic diagnostics when the protection mode is turned on;
  5. shutdown protection with sound or without;
  6. Disable the engine lock in two stages.

The main distinguishing feature of this alarm among others in the same price category can be noted:

  • The presence of a convenient dialogue 128-bit control code, through which none of the known codegrors cannot be made (devices to read the system code);
  • Ergonomics and resistance to extreme weather.
  • For such a price, it will be difficult to find a more frost and heat-resistant security device for your car, and the battery capacity will allow the alarm to operate in the protection mode for one and a half or two months;
  • You can be sure that in the zone of the signal, and this is from 800 to 1000 meters, there can be no interruptions in the operation of the alarm - all radio interference, which often arise in urban environments, will be held with the help of a specialized transceiver;
  • Alarm and keychain work with modern software that significantly increases the speed of the system than on more obsolete models

STARTLINE A91 functional with autorun meets all stated distinctive features - modern software associated with hardware properties provides productivity and high degree of vehicle protection. All functions can be divided into two parts: on security features of the device and on service functions (mainly associated with the use of key fob). All service functions will be described in detail in the appropriate subtitle.

Startline A91 Alarm Connection Scheme with Automotive

How to change the temperature on the alarm STARLINE A91

Many security systems have additional options and opportunities that facilitate life to their owner. For example, Starline A91 is autorun. Moreover, it can be installed on any car, including such models as a VAZ 2110 or 2114. The diagram of connecting the car alarm is quite simple and can be carried out in the garage. This will require:

  • Set of a security system;
  • a set of tools including drill, drills, screwdriver, etc.;
  • Soldering supplies: Soldering lamp, solder, tin, rosin;
  • Isol, shrink tubes and industrial hair dryer.

The diagram is shown in the figure below.

For remote motor start, you need to connect a special six-contact connector. In this case, the wires are connected in a certain order.

  • Red cable (+ 12V) goes to the central lock;
  • Yellow (IGN1) - cable for ignition lock;
  • Two black wires are connected to the starter (thick) and ignition lock (thin);
  • Blue and green remain not connected.

How to make autorun with buttons

After the correct installation of the car will be able to hold a remote launch. Additionally, a number of functions for programming will be available. Starline A91 can be configured to autorun on temperature, alarm clock, time or charge of the battery. Below is the video in which it is explained which buttons must be pressed.

The owner can also start the motor remotely at any time, if there is a key chain. The key combination in this case is a long press of the first key (to the beep), and then a short click on the third button. At the same time, the car must be put on neutral (for models with the manual transfers neutral programming), the hand brake is tightened, and all the doors are blocked.

Setting the STARLINE A91 alarm on autorun time

The security system has a function of setting the remote start time. This feature allows you to start a motor at a specified hour, as well as warm it to the arrival of the owner. If the first start attempt failed, the next time the starter time is increased by 0.2 seconds. After four unsuccessful attempts on the keychain comes the appropriate alert.

How to set the time of autorun

In order for the function to work correctly, you need to put the correct time on the key chain. After you need to enter the programming mode, by pressing the VALET service button in the cabin six times (when the ignition is turned off). After turning the key to the ON position, the car will publish 6 sound signals.

Now click the service button three more times, turning into the appropriate programming mode. For each pressing the machine reacts the audio signal. After that, within ten seconds, on the keychain, you must press the desired button (the first key - each two hours, the second - three hours, the third - four hours). Confirmation of the procedure will occur independently.

Turning on the STARLINE A91 signaling in time

In the cold climate conditions, the option of periodic autorun time is extremely useful. And the STARLINE A91 system has this feature. To turn it on, it is necessary to push the third button until the second melodic signal. After that, the left icon on the panel flies. Another press of the button three moves the cursor to the fan icon, and the short press press confirms the choice.

Time autorun shutdown

If necessary, you can refuse this function. Disconnection occurs as follows:

  • long (to the second signal) button 3 is pressed;
  • The cursor moves to the fan icon;
  • Deactivation of the function is carried out by short-term pressing on the second button. In confirmation of this car, the headlights twice the headlights and emit a signal.

Starting an engine for alarm

You can configure your own start of the engine in the alarm clinic. To do this, you will need to first configure these parameters on the keychain itself. Press button 3 before playing a small melodic signal. After that, the clock parameter on the remote must be filled. Two more short presss allow you to go to setting the alarm settings. The desired values ​​are set by clicking on the keys 1 and 2.

To activate the autorun function, you must consistently press the third and first key (after that the clock icon flashes, the melodious sound will sound, and the car will respond to the flash of the overall signals). Using the buttons 1 or 2, you can set the necessary parameter. Then the third button is pressed again, and after the key one (confirmation of the activation of the alarm clock). Another long pressing of the third button allows you to activate the alarm autorun mode.

Changing the warming time to Starline A91

Depending on the selected settings, the car can warm up 10, 20 or 30 minutes. This parameter is programmed after entering the service mode:

  • Turn off the ignition and press the VALET service button six times in the cabin;
  • turn on the ignition, listen to six sound signals from the car;
  • Two twice the VALET key is clicked;
  • The next click buttons keychain defines the warm-up time (the first key is 10 minutes, the second - 20, third - 30). Confirmation of the command is made automatically, do not press anything enough.

How to enlarge start-up time with STARLINE A91

It happens that the machine does not start in cold conditions, if the starter works around a second (factory settings Starline A91). In this case, you can extend the time of its work. The instruction is as follows:

  • When the ignition is turned off, you must press the Valet service button six times to go to programming mode;
  • After turning the key (ON) the car blinks six times with dimensions. Then you need to press the VALET key for nine times;
  • Pressing any button on the keychain determines the speed of the starter (the first - 0.8 seconds, the second is 1.4 sec., the third is 2.0 seconds). Long plus a short click of the first button - 3.6 seconds.

So that the starter does not twist when the work engine must be connected gray with a red wire on the panel tachometer for automatic stop.

Setting the alarm STARLINE A91 on autorun temperature

Car alarm has a launch mode at low temperature, which is extremely useful in cold climates. This option is programmed as follows:

  • Turn off the ignition, press the VALET key six times;
  • we turn on the ignition, click Valet four times;
  • Now the first button on the key chain will set the parameter -5 degrees, the second - minus 10, the third is minus 18. Long, and then the short press of the first button is responsible for setting the parameter - 25 degrees Celsius.

How to set autorun on the engine temperature keychain

Now the basic parameters are set, it remains only to activate the autorun function by temperature:

  • Press a long key for a long key, up to the second melodic signal, which will play the keychain;
  • Two twice by clicking on the third button so that the cursor on the display moves to the icon with the thermometer;
  • To activate, you must click on the first key once.

Now the car will start with the temperature owner.

Disconnection of autorun temperature

If the owner of the car for a long time leaves or automatic launch at a temperature is not necessary, then this function can be removed. The procedure occurs in the same way:

  • We click the third button for a long time (to the second beep);
  • Two two times click on the third key to briefly to move the cursor to the pictogram of the thermometer;
  • The second button deactivate this feature.

Startline A91 Alarm Operation Manual with Automotive

There are several points required to properly activate the autorun function. This applies not only to the Starline A91 system, but all similar alarms. To activate this option, the car must be put on neutral (for machines with automatic transmission - Parking mode), the handbrake must be tightened, and all the doors, hood and trunk - closed tightly. Below is a detailed instruction manual.

Read instructions

Why autorun autorun does not work

Sometimes it happens that the autorun function does not work. For example, the starter turns the engine, but it does not start. In this case, it is necessary to check the presence of gasoline in the tank, as well as the charge of the battery. In the first case, everything is clear - it is necessary to add gasoline. In the second - to charge the battery.

It is also possible that the motor does not grab on the cold and even badly start from the key. In this case, you can set the settings at which the starter time will be increased. You can also reduce the interval between start-up attempts.

But the most common reason why the car does not start, becoming banal inattention. Such reasons include the transmission included (for vehicles with automatic transmission Drive), unlocked door lock, etc.

It happens that the car stopped starting because the system badly catches the signal.

In this case, the keychain issues information and immediately writes an error. To reset the protocol, you must start the motor from the key again, tighten the handbrake. Then get the key from the ignition lock, open the driver's door and activate the alarm. Typically, the car again arises to protect, and the OS7 error simply disappears. However, it happens not always. If this did not happen, you must contact the service center.

What if the autorun does not work

If the car does not start independently, some problems can be solved with your own hands. For example, after replacing the battery, the clock is knocked down and all settings flies, which means that the car will not start at that time. Be sure after the new battery is installed in the console, the correct clock is set.

It is also necessary to check the console itself. It may be damaged - have cracks on the display, mechanical damage or tritely discharged battery. In this case, the signal is not transmitted remotely, respectively, the remote start does not work. In order to understand how much the key chain is "to blame, you need to configure the launch from the phone (the instruction is described above). If even after that the problem does not disappear, you need to spend thorough diagnosis.

How much is the key chain Starline A91 with auto start

The price of the security system depends on the configuration of the set. For example, in Moscow, car alarm costs from 4 thousand rubles, and if there is a GSM module, the cost increases to 9 thousand. For other cities of Russia, this figure may vary.

City The cost of Starline A91, thousands of rubles
Moscow 4-9
St. Petersburg 4.2-8,8.
Yekaterinburg 4.4-7
Saratov 3.5-6.8.
Volgograd 3.8-7,3

Reviews

Gennady, 35 years old:

Recently took the car, it was already StarLine A91 installed. I will say so - very advanced car alarm for your money. Very good feedback - on the key chain it is immediately clear what is included, although there is a whole bunch of different indicators. And the display itself with good illumination, even on a sunny day does not turn out and remains informative. In general, it suits me completely, I think that this system would put on another car.

Mikhail, 38 years old:

Starline A91 chose after long reflection. I say that I did not lose. On your money just excellent alarm. There is everything that can be autorun, feedback and turbo -mer, which is very important to me. Each parameter is configured separately, which is convenient.

In the morning I drink coffee, and then I go out and sit down in an already warm car, thanks to the autorun. And it is also cool that you can put the GSM module and manage some features directly from the phone. It is really convenient.

Especially for the price in which Starline A91 is estimated.

Material author: Borisov Maxim

A source: https://rus-avtomir.ru/beep/starline/avtozapusk-a91

STARLINE A91 Alarm: Operating Instructions, Autorun, Installation, Connection

Starline A91 Dialog - Modern Car Alarm. Security characteristics of the system are made on innovative technologies.

User's manual:

Installation Instructions Instructions

Setting the key fob, buttons designation:

Button 1. • Enable audio confirmation security mode (single pressing) • Enable protection mode without sound confirmation (sequential pressing) • Turning off / turning on the shock sensor over levels (double pressing) • locking door locks when the ignition is turned on (single pressing)

Button 2.

• Turning off the COP COP mode (single pressing) • Turning off the security mode without sound confirmation (sequencering) • Turning off / turning on an additional sensor over levels (double pressing) • Unlock door locks when the ignition is turned on (single pressing) • Turning off the anti-labeling mode (two Single pressing) • Interrupt alarm (single press)

Button 3.

• Alarm and Temperature Status in the car (single press) • Turning the "Search" mode and engine temperature control (double pressing) • Activation of an additional channel number 3 (sequential pressing) • Activation of the cursor selection of the following functions: automatic launch of the wake-up, automatic launch Timeru, automatic launch of waste, service mode, turbotimer mode, modimmobilizer, automatic switching on the security mode (long press) • Enable the current time setting mode, alarm time, timer, on / off alarm clock, timer

Buttons 1 and 2 sequentially

• Inclusion of silent protection

Buttons 1 and 3 sequentially

• Engine launch or extension of the operation of the engine already running

Buttons 3 and 2 sequentially • Activation of additional channel number 2

1 + 2 buttons at the same time

• Turning the "Panic" mode (long press when the ignition is turned off) • Turn on the anti-label mode (long press when the ignition is on)

Button 1 + 3 at the same time

• Turning on the lock buttons keychain (single press)

2 + 3 buttons at the same time

• Turning off the lock buttons keychain (single press)

Short press button - One press of any button lasting less than 0.5 seconds. Long press button - Pressing and hold the keychain button before the melodic sound signal appears. Double button pressed - Two pressing of one button for 0.5 seconds. Sequential press of buttons - Two clicks of one or different buttons. The first press should be long, the second press is short-term.

Setting time by keychain:

1) Press and hold the number 3 button to 1 melodic signal2) 1 short signal3) 2 short signals

4) The clock button flashes: Button No. 1 - Increases the readings, button # 2 - Reduces the readings

Turning on the autorun:

Press the key chain number 1 for a long time, then button number 3 briefly.

Installing a timer autorun:

Timer autorun mode. One of the types of automatic engine start. Allows you to perform a periodic start of the engine every 2, 3, 4 or 24 hours, depending on the choice.

1) Briefly press the №32 button) The timer clock icon flashes: Button No. 1 - Increases the readings, button # 2 - Reduces the readings

Installation of autorun temperature:

Autostart mode for temperature. One of the types of automatic engine start. When the engine temperature decreases below the set threshold, the engine will automatically start to warm up.

1) Briefly press №32) The temperature icon flashes: Button No. 1 - increases the readings, button # 2 - Reduces the readings

Connection diagram:

Alexander Lobanovsky Kharkov graddermatovenenerologist

A source: http://signalizaciya-starline.ru/modeli/signalizaciya-starline-a91.html

Starting a car engine - installation of car alarms Starline B9 Dialog

Before launching the engine with a keychain or inactivate the automatic engine launches, it is recommended to familiarize yourself with the flight features of the launch functions.

Engine:

  1. In order to successfully implement the functions of remote or automatic engine launches, the following parameters must be programmed at the Installing Stage:

    - Car gearbox type - manual

    Transmission (RCPP) or automatic transmission (automatic transmission). To do this, on cars with the RCPP, a black loop in the wiring harness of the 18-pin host of the central unit is necessary. On cars with an automatic loop, a high-contact jack of the 18-pin connector must be saved.

    - Type of car engine - gasoline or diesel. For

    This, log in to the programming mode of the function 2.10 and depending on the type of engine, set the required starter turning on after turning on the ignition of the engine attempt. For diesel engines for the inclusion of the starter necessary for warming up - 4, 6, 10 seconds. For gasoline engines, retained - 4 seconds. - For vehicles with the start button - Program

    Function 8 (Table 2) for option 3.

  2. The remote engine start can not be embedded: ignition is on, the hood is open, the parking brake is turned off or the foot brake is pressed, it is not fully prepared for the engine start on cars with

    RCPP.

  3. For one start cycle, the system can take 4 attempts of the engine. If, after the 4th attempt, the engine is not enough, then on the display with feedback (skeleton, that it is in the reception area) appears "SP", and the keychain will give 4 beeps, indicating the ending

    Attempts to start the engine. Four outbreaks of dimensions will follow.

  4. The maximum time of the first scrolling attempt starts to be programmed when the signaling is installed0.8; 1.2; 1.8 seconds or 3.6 sec for any method of controlling the operator. The time of each subsequent scrolling attempt for one start cycle automatically

    Increases 0.2 seconds.

  5. If the engine is running until the starter scroll expires, the starter turns off early.
  6. If the engine running will stroke until the warmed warming time, it will be undertaken

    New engine start cycle.

  7. The automatic engine start function by temperature to be turned on regardless of the status of functions

    Automotive motor in the alarm clock or by timer.

  8. The simultaneous enabling the functions of the engine automatically over the alarm clock and on the timer is impossible. Reading the simultaneous turning on the functions will result in the query that has been activated

    The latter.

Preparation for launching on car manual gearbox

Before launching the engine on cars with RCPPNOCly, perform the procedure of "software neutral". The program neutral is a specific procedure for the accommodation, which guarantees what in the car prepared for launch, the switching knob is transmitted in a neutral position. Accordingly, starting

The engine will not be possible when the transmission is enabled.

Software neutral Depending on the status programmed function 12, Table 2 can be performed

In two versions automatic or controlled keychain.

Inclusion of "software neutral" Automatic option - Car alarm StarLine B9 Dialog

Engine prepared for launch

The inclusion of "software neutral". Transfer control keychain.

Engine prepared for launch

Remote Engine Start Selfing Single Glass Starline B9 Dialog

Before turning on the mode, make sure that the hood is closed. For automotive with a manual box, the "software neutral" procedure is performed. For cars with automatic

Control lever box in the PARK position.

For one start cycle, the system can take 4 attempts of the engine. If, after the 4th attempt, the engine will not be hit, then on the display with a feedback (silt, that it is in the reception area) will appear the inscription, and the keychain will give 4 beeps, indicating the ending

Attempts to start the engine. Four outbreaks of dimensions will follow.

1 minute before the end of the engine warming, the R01 is displayed and the 2 series of 4 audio signal sounds.

After the end of the engine warming up the engine and its automatic stop, 4 outbursts will appear. Nadisplay keychain will display the R00 icon, 4 sounds will be performed

Signal keychain.

Automatic engine launches

Automatic start of the an alarm clock (activated with the keychain)

  • To enable the automatic engine start function to set the alarm on the alarm, the keychain first check the installation of the installation time on the keychain. Then program the alarm clock edge of the engine starting time and turn on the alarm. Turn the an alarm mode on the keychain display is displayed by the icon. After checking the current time and set the alarm to serial the buttons 3 and 1 keyword, set the cursor to the icon and turn on the alarm. 1 outbreak of dimensions will follow. The melodic beep sounds the keychain and appears on its display, indicating together with the icon on the entered alarm mode. For a short time on the display of the keychain, the last time of the future startup, which will then change to the current time. The LED will flash a series of 2 outbreaks.
  • To turn off the autorun function on the alarm, re-install the secret command to the icon and click the 2 keychain button. Follow 2 flabbarites. A melodic signal keychain, icons, will disappear.

Note

  1. The presence of a keychain in the zone of the receiving transmitter at the moment of the autorun of the engine on the alarm clinic is not required.
  2. The engine start time may differ from the programming alarm clock within 1 minute.
  3. The autorun function is turned on by one start cycle. For a new start, each time you need to activate the function with the keychain.

Programming and configuration of the automotive security system can be carried out after installing car alarms in the company "Fazis Orbit Service".

Automatic start of the timer engine (activated with the keychain)

  • To enable the automatic engine launch function by timerhouse 2, 3, 4, 24 hours (programmable function 2.3), using the buttons 3 and 1 keychain, set the cursor to the icon and turn on the timer. Follows 1 outbreak of dimensions. The melodic signal keychain seems. The keyboard display shows an icon indicating the included timer autorun mode. The LED will flash the series of 2 outbreaks. Simultaneously with the inclusion of the function, the engine is launched and its heating during the registered time.
  • To turn off the timer autorun function, re-set the cursor icon and click 2 keychain. Two flash of dimensions will follow. Through a melodic signal keychain, the icon will disappear.

Automatic start of the engine at a temperature (activated with the keychain)

Auto alarm allows you to automatically start the engine at the duplicate temperature sensor fixed on the engine, the temperature is programmed -5 ° C, -10 ° C, -18 ° C or -25 ° С (Function 2.4). The engine time is determined by the programmed function 2.2.

The automotive security system monitors the sensor readings immediately from the moment of activationifunction. The minimum interval between repeated autoruns, counted since the previous launch without taking into account the heating agent time - 1 hour.

After activating the temperature of the temperature launch

The number of auto-starts of the engine at a temperature is not limited.

  • To enable the automatic engine launch function by temperature, the cursor on the icon and turn on the autorun temperature. 1 outbreak of dimensions will follow, and the melodic signal ring will sound. The keychain display will display an icon indicating the on-temperature mode, and the temperature value at which the engine can be launched, for example. The LED indicator will blink 3 outbreaks.
  • To turn off the autorun function at a temperature, re-installed on the icon and click the 2 keyword button. Follow 2 flabbarites. A melodic signal keychain will sound, the icon will disappear.

Starline

Installing car alarms StarLine A2 Installation of car alarms StarLine A4 Installation of car alarms StarLine A6 Installing car alarms StarLine A8 Installing car alarms StarLine A9 Installing car alarms StarLine B6 Installing car alarms StarLine B6 Dialog Installing car alarms StarLine B6 Dialog CAN F5 V100 Installation of car alarms StarLine B6 Dialog CAN F5 V200 Installation of car alarms StarLine B62 Dialog Flex Starline B9 Diagnostic Installation Installation Installation Instructions Starline B9 Dialog Installation Instructions (Specifications and Equipment) Recommendations for placement, installation and connection Connecting various circuits Programming service functions Description of programmable functions Programming Engine start settings Description of programmable startup functions Starting the engine Signatures and batter elements keychains instruction manual (security and service alarm) keychains Say alarm setting Function Single Running Function Samples Programming Speed ​​Cursing Mode Turning On Alarm Protection Modes Control and Self-Diagnostics Alarm Alarm Signals Protection From Turning Off Power Mode Immobilizer Mode Anti-RAM MODE TURBOTEMER SENSOR Channel Engine Run Running Car Motor Installation Starline B9 Dialog CAN F5 V100 Starline B9 Diaalog Installation Installation CAN F5 V200 Installation of car alarms Starline B92 Dialog Flex Installation of car alarms Starline B94 Dialog Installation of auto alarms Starline C4 Installation of car alarms Starline C6 Installation of car alarms Starline C9 Installation of StarLine 24V

Installing the Moto V5 Motorization Motorization, Motorcycle Alarms

A source: http://www.autoradioservice.ru/signalling/starline/b9_dialog/start_engine/

Autorun Starline: How to configure Starline alarm

Starline alarm is a modern security system that meets all vehicle protection requirements. Also, the STARLINE Alarm, provided that the installation and settings are properly installed, allows you to remotely turn on the start of the car engine (manually or automatically starts at temperatures).

At the same time, the owners of vehicles without going into details or without having fully implemented the installation instructions, do not always know how to configure the alarm STARLINE, turn on the autorun Starline, etc. Next, we will look at how to configure the autorun on the alarm Starline, given its technical and structural features.

STARLINE STARLINE: Autostart with a keychain and automatically

In the autorun system, the STARLINE provides the option of the intelligent launch of the engine, when the alarm for communication between the main unit in the car and the keychain independently selects the frequency.

Thanks to such peculiarities, the interception of the signal of the security system is almost impossible. This is especially important in urban conditions and conditions of an increased level of radio interference.

Regardless of the alarm model, before installing the Starline autorun, you must learn the instruction manual (Description of the main settings and various mode of DVS launch).

Methods for launching a car engine:

  • remote launch (warming the car before starting traffic);
  • Automatic launch (periodic start of the car engine at certain time intervals to maintain the temperature by a given value).

Remote autorun Starline

Before viewing how to enable autorun to Starline, you need to pay attention to some features. To properly configure autoruns with a keychain, you must perform the following steps:

  • Transfer the gearbox lever to the "Neutral" position (all transmissions are disabled);
  • Rotate the key in the ignition lock and get from the lock (engine engine is dried);
  • Tightly close the doors, the lid of the trunk and the hood of the car;
  • Enable parking brake (handbrake).

Performing all these conditions allows you to start the car's engine remotely. We now turn to how to turn on the STARLINE autorun. First of all, to install the car into the protection mode with the "Starline autorun" function, you must perform the following actions algorithm:

  • stop the movement of the car, not turning off the ignition (the engine of the car is instituted);
  • translate the gear lever to the "Neutral" position (transmission off);
  • put the car on the handbrake (the parking brake is on);
  • Pressing the "1" button on the keychain, hold it for 3 seconds until the sound melodic signal occurs;
  • Turning the key in the ignition lock, get it out of the lock (the car does not stall);
  • Coming out of the car, make sure the door closure density, luggage compartment and the hood;
  • If everything is done correctly, the alarm will muffle the engine and blocks the doors of the car (the protection mode is on).

Note, only correctly performed actions will allow you to start the car's engine remotely. Otherwise, the autorun function may not work.

So, remote autorun to Starline is available with proper preparation of the car. Observing the entire algorithm described above, the car can be started with the keychain in different ways:

  • The first method - by pressing the "1" button and hold it for 3 seconds before the audio signal appears to quickly press the "3" button;
  • The second method - choosing the "Start" icon, press the "2" button (relevant for the periodic engine warming in the winter season).

Due to the actions taken with a keychain:

  • Alarm makes the first attempt to start the car engine;
  • If the car engine did not start with the first attempt, the alarm makes the second, the third or fourth attempt (the starter time of the starter is increased by 0.2 seconds);
  • If the car engine did not start after the fourth attempt, the key fob will invoke four beeps;
  • If the engine started, the "Exhaust gas" icon appears on the display (on different Starline models, this icon may have differences) and the dimensions of the car are blown three times accompanied by a siren signal;
  • Warming of the car of the car will be carried out in accordance with the time interval, in advance set in the settings (5.10.15 min, etc.);
  • A minute before the end of the specified temporary interval, the R01 icon appears on the display. If the time is over, the alarm swallows the engine and the icon on the display of the "Exhaust gases" keychain changes to the "R00" icon.

Autostart Starline by temperature

In the winter season, many motorists have the need to warm their car at night. When setting up autorun on temperature, some moments must be taken into account: the presence of a temperature sensor, the location of the sensor and others.

When the autorun is turned on, the STARLINE temperature sets the value of the ambient temperature, when the car engine is reached (-5 ° C, -10 ° C, -20 ° C, -30 ° C).

Sequence of steps to turn on and off autorun temperature:

  • By selecting an icon with a thermometer and the inscription "START", press the "2" button on the keychain (after the audio signal, the value of the temperatures of the temperatures installed) is displayed on the display);
  • When the autorun is turned off at a temperature, you must select an icon with a thermometer on the display and click the "2" button on the keychain.

Note, when you have the need to get into the car while the engine is warm up, you need to press the "1" button on the alarm keychain (locks are unlocking).

Once in the cabin, for 30 seconds it is necessary to have time to turn on the ignition, inserting the key to the lock and turn it. To fully exit the autorun mode, you need to release the manual brake, while the dimensions of the car are blocked once, after which a beep will occur.

Let's summarize

The actions described above and recommendations, how to include autorun to Starline are almost the same for all models, but small differences may be. For this reason, it is recommended to study the manual for specific models separately.

Finally, we note that as a result of errors, the autorun functions may not work correctly work when installing or improper operation. In other words, it is important to comply with the correct execution of consecutive actions that are written in the Starline instruction.

A source: http://krutimotor.ru/starline-avtozapusk-kak-nastroit/

How to set autotypers on Starline alarm

The STARLINE A91 security system refers to the class of budget alarms. Despite this fact, it provides all the necessary functions to protect the car, and the anti-theft complex itself meets all applicable requirements. The data stream, in Starline A91, passes on eight changing channels with a 128-bit encryption code.

In addition, the system includes an option of intelligent engine start. Thanks to such features, it is extremely difficult to intercept the signal of the security system, because the alarm selects the frequency independently, for communication between the keychain and the main unit in the machine. Such a feature, in the conditions of the city and an increased level of radio interference, plays a key role.

How to start a motor with a console

As noted above, the STARLINE A91 signaling is provided for the function of the remote engine plant. But before setting up the autorun, perform a few steps:

  • Move the PPC knob to the neutral position (disable all transmissions).
  • Turn the key to the ignition lock and get it. The engine must be muffled.
  • Cleve the hand brake.
  • Close all doors well, lid luggage compartment and hood.

To successfully configure autorun, it is important to clearly follow the algorithm. Otherwise, the remote start fails. If the car is properly prepared (the motor is dried by Starline A91 alarm), it can be started with the keychain in various ways:

  • Press and hold, for three seconds, the 1st button. Once you will hear a beep, press the 3rd key.
  • Configure the periodic engine start from the remote control.

This option is especially relevant in winter when necessary, from time to time, to warm the motor. The STARLINE A91 control panel is capable of automatic mode, start the engine and ensure heating it, with the necessary frequency - every two, three, four hours or times a day.

Configuring automatic launch at temperature and time

The safety feature of the STARLINE A91 system dialog is the convenience of setting up autorun. The latter can be adjusted in such a way that the function will start the motor, with a decrease in temperature to a certain level, or in a specific time interval.

Turning on temperature autorun

To set up a temperature autorun, consider some conditions for the correct operation of this option - the place of installation, the presence of a temperature sensor, as well as its serviceability. To activate the function, do a number of steps:

  • For a long time, press the 3rd key (with the image of the "asterisk").
  • Wait for the appearance of a sound signal from the console (the sound must be one-time).
  • Look at the display - the icon located on the left side will flash on it, at the bottom of the display.
  • Briefly press on the 3rd button, then move through the menu, to the thermometer icon (third left).

Once you have verified that the required function is set on the alarm, press the 1st button to activate the mode. If it is required to shut down, click on the 2nd key, on the housing of the keychain. Now look at the display - at the place of hours, the motor temperature parameter should appear, at which the autorun will work.

After highlighting the temperature, you do not need to do anything - after 8-10 seconds, the StarLine A91 keychain will give a signal, and the clock will appear on the screen. At the same time, the 3rd icon with the thermometer remains darkened. According to the appearance of the image, it is possible to control the correct setting of autorun temperature. If the light icon is disabled, and if the dark is activated.

Time autorun setting

To enable this option on the STARLINE A91 alarm, select the 2nd icon on the display. At the same time, the headlights of the machine must blink once, and the key chain of the security system to serve as a ringtone. This time setting up the time has been completed. The system will independently give a command to the engine factory, at a certain time.

If the machine from the first attempt did not start, the second is done. At the same time, the starter time is automatically extended by 0.2 seconds. The device's timer laid four attempts to start the motor. If all of them are spent, but the engine does not start anyway, the beep will work on the StarLine A91 remote control.

To set up autorun time, take the following steps:

  1. Press and hold, for a long time, 3rd button on the alarm keychain (the "*" symbol is drawn on the key).
  2. The console will apply short-term sound, but hold the button before the second signal appears. After that, release the key. Icon on the left side (in the very edge of the screen) must be filled.
  3. Put on the 3rd button, then move to the icon with the image of the fan.
  4. Make a short pressure on the 1st key. The latter must publish a melody.
  5. Look out 10 seconds, until the key chain again displays a signal. The image of the fan should remain darkened.

If the considered manipulations are made correctly, the autorun setting is completed. Now the STARLINE A91 alarm will submit a command to start the engine, with a certain interval.

Turning off the option is made via a similar algorithm. The only thing that confirmation is made using the 2nd button on which the open lock is depicted. If the engine start is successful, the display appears on the display, with the image of exhaust gases. The headlights of the car should be blinking three times, and the Clavon signal is fed three times.

Why autorun does not work - the main reasons

In the process of operation of the machine, there are situations where the STARLINE A91 autorun does not work with the keychain. The reason for such a phenomenon is usually associated with a failure of one of the details, but with errors in operation or configuration. In case of failures in the operation of automatic launch, problems may arise with the setting of the car.

A source: https://nadouchest.ru/kak-vystavit-avtoprogrev-na-signalizacii-starlajn/

Auto start in the STARLINE A91 Dialog signaling: Connection, Setup, Tips

The STARLINE model of the A91 model is in two versions: StarLine A91 Dialog, as well as A91 4 × 4. The first of them is released so far, and all the differences, oddly enough, consist in the form of a key fob and in icons on its display. Connection diagrams of the first and second signaling are no different. There are no differences and in configuration methods.

The second model will be called this: Starline Twage A91. And it will be considered that which typical errors are allowed trying to implement autoruns with the specified signaling. The absence of either the low reliability of engine operation control is the main error that can cause severe consequences in reality.

Methods for monitoring the operation of the DVS

Suppose, the "black and gray" wire from the main 18-pin connector was connected to the output of the tip or to the battery charge lamp:

Automotive Options, model A92

Here you see customizable functions that are responsible for automatic launch. The table is copied from the installation instructions. By the way, do not look for it in the instruction manual.

We assume that the connection and configuration are made. Check that the automatic start terminal bar (6 wires) is connected according to the instructions. Next, you need to disable the security mode to perform the following check:

  1. The key is translated to the ignition label, the starter starts are not performed, the key 3 is pressed on the keychain;
  2. By starting the engine, a button 3 press button on the keychain and control the display state.

As stated in the instructions, in the first case, the display must display the key icon. In the second, the image of smoke is added to it:

Checking the operation of the engine

The STARLINE TWAGE A91 keychain displays the icons shown below.

Perform work on errors

In theory, any car alarms listed here has properties. The presence or absence of difficulties in the setting is due to the car schemes, and not the malfunction in the security system.

Starline, however, supplied the user with instructions on how to solve the problems arising. For example, such an effect can be observed: at a low temperature, the launch is carried out "times", and there are no problems in the warm season.

So, most likely, control "on the charge lamp" is used, and the voltage at the generator output appears too early.

The generator must work so

Change the sensitivity of the control scheme would be meaningless, and in the 36 line signal this option is not provided. Use another method, for example, the test batch.

If you can configure control over the generator, you can also not always, then the question arises, is it not easier to control only the voltage. Do not follow the programming of the function 11, and get this option immediately. And then try to perform the verification procedure. In almost every modern car, it will fail.

There is a advice that does not lead in any instructions or in reviews. By connecting the "black and gray" wire to the charge lamp, try to use both options for setting - 2 or 3. If it does not help, connect to another lamp contact. But the best method, as the Starline experts themselves say is reading the engine tip signal.

Pulses of the DVS DVS

To implement such an option, the control cord is connected to the high-voltage tachometer terminal. You can use the output control, if we are talking about injectionboxes. Then adjust the sensitivity of the signal input, and more this operation is considered in the following chapters.

In the function of more complex systems that do not belong to the family of the Star Line dialogue include control of the operation of the engine on the oil pressure sensor. The method perfectly works only with some engines, and low temperatures it gives failures. Use exactly the method of control that is reliable during operation in different conditions.

Connection features, setup

Consider the scheme that the StarLine A91 Dialog system is installed.

Locking on the brake

See where the voltage appears when you click on the pedal. Take into account that when you assume the error, everyone will have to be disconnected - use the coupler.

Programming function 8 is allowed to be performed both before and after connecting the cord in the "blue" insulation.

It remains to consider that it is necessary to program that the "pink" signal cord is correctly controlled by a cross-country. There are options responsible for the "behavior" of the StarLine A91 Dialog system during its operation. There are no such settings among them. Well, the functions responsible for autorun, also do not contain anything like this. The algorithm of the work of the manager will always be one. As we considered the necessary experts old line.

In fact, it is better to check whether the cord is connected correctly in purple-orange isolation. When operating the autorun, you need to activate the "handler", and the specified wire reads the signal just from the brake microcopters.

Connect the crossover will be easy. But the Instructions of the Star Line does not say the following:

  1. Despite the dialogue regime, it is easier to sobally a car with a correctly installed by the crawl than without it;
  2. The attacker will turn off the immobilizer, simply by clinging the cord on the ground, and there is no problems with hacking locks today;
  3. As soon as the autorun is implemented, due to the increased probability of hacking, the cost of CASCO will immediately increase.

Everyone who needs autorun, with the presence of a side speaker will have to accept. Full car "guard" is too primitive to understand commands from external devices. So you have to connect bypass, in the absence of which the remote or automatic launch does not work.

Ignition Castle Locks

We wish you success.

Setting the alarm from zero

To change the values ​​of the functions listed in Chapter 1, you need to perform the following:

  1. Let the automotive security system be in "removed from protection" mode. Ignition should be turned off, and then 6 times press the Valet service button. In each system of Ultra Star, this element is present.
  2. Turn on the ignition without running the engine. 6 siren signals should be sounded if the latter was connected. Usually during operation, siren is turned off.
  3. Change the number of the option is customizable at the moment, can be single-click on the button.

To exit the programming mode, you need to turn off the ignition or do nothing more than 9 seconds. Change the value of the function by pressing the key fob key. For the StarLine A91 signal Dialog, the instruction is fully suited, and there are no differences for the twnet version.

Note: You can configure the start, but not shutting down the operating engine by temperature.

The main key chain STARLINE A91 looks like this:

Basic Signal Base Set

To set a value equal to 4th, button 1 is pressed for a long time, and then briefly. When operating, this option is also used - it allows you to enable protection without a sound signal. For STARLINE TWAGE A91 systems, there will be no fundamental differences: there the keychain is also endowed with three buttons. Reset settings are performed as follows:

  1. Instead of 6 pressures use 10;
  2. After 10 audible signals, the VALET button is pressed;
  3. After a single short-term "bipa", you pick the key 1 on the keychain.

If the control is used by the touchscreen, configure the sensitivity of the programmable input. The procedure is called "learning", the truth is not used in the instructions.

You can only view the values ​​of each function on the disclosure of the keyfoot that runs in the dialog mode. It will not be necessary to change these values.

Teach the STARLINE A91 Dialog signaling to recognize idle turns in reality is not easy. You must first turn off the "yellow" wire connected to the "15" terminal, and before the start of operation, everyone is returned to the same mind. When the cord is disabled, perform actions:

  1. Close the doors, hood, trunk;
  2. "The handbrake" deactivate;
  3. Perform the engine launch;
  4. The motor should work at idle;
  5. Sensitivity will be configured automatically.

The StarLine A91 Dialog system is also provided with the VALET button, and the LED indicator. If learning is successful, the diode flashes. In any review, of course, do not talk about the difficulties considered here. And the instruction contains the following short text.

Screenshot of installation manual

What you need to know the owner

Starline A91 Dialog alarm can be configured both on the table and the cursor method. Configuring autorun on temperature, go to the "Thermometer" symbol, but if the sensor is faulty, the icon is not activated.

Screenshot of the leadership of ultrastar

Such functions could not be implemented if the dialogue mode was not used. In each review, where the Security Complex Starline A91 Dialog is considered, praise and resistance to hacking. All of these characteristics, as can be understood, are related to the presence of a dialogue mode.

There is a review, where the range of communication with the keychain was measured during testing. When operating, it is obviously several other values ​​other than "passport" are obtained. For the STARLINE A91 Dialog signaling, the following results were obtained:

Test of communication range

The command filed by the system from the key fob was just started starter. Characteristics here look good, but to several kilometers specified in the documentation, they obviously do not reach.

In responses published by the owners, report information inaccessible in any review:

  • Using the mode dialog entails and negative consequences - the battery is quickly discharged in the display with the display. This effect itself is stronger at low air temperature.
  • The automotive security system of the model under consideration has its own specific disadvantages. After several seasons of operation, for example, you have to configure the shock sensor, turn it off or replace it new.
  • Automotive temperature can be used. But the thermal sensor is better to fasten under the torpedo, and not on the engine crankcase.

Information from the list may refer to the StarLine A91 Dialog signaling, but not only to it. Ultimately, its processor program provides 3 autorun modes: in temperature, and at certain times (alarm clock) or by timer. Combined mode can be used too. Select the choice for the future owner.

Keychain A91, its options

A source: https://autolocked.ru/avtosignalizacii/starline-a91-dialog

How to set the motor autorun? Starline alarm system

Updated Jun 10, 2019 12 635.

With the arrival of cold weather, many drivers face the inclusion of the remote autorunning of the engine or the launch of temperature. Starline alarm allows you to do if it was correctly installed and configured. Many car enthusiasts simply do not know how to enable and configure the autorun of their car. There may be many reasons for this - forgot, they did not go into details, just bought, they were leased, etc.

Setting up autorun- STARLINE Alarm

First you need to understand that the engine starts two species - Remote or automatic . Remote launch is needed for example in order to warm up the car before starting the movement.

Automatic engine start involves periodic engine launches, such as at night, to maintain the desired temperature.

The autorun can be configured in such a way that the auto starts at certain time intervals or when the temperature decreases below the specified value.

Conditions for autorun

Remote engine start can only be performed under the following conditions:

  • Gearbox handle is located on neutral (transmission off)
  • Ignition off
  • Hood, trunk and all doors are tightly closed
  • Included parking brake (handbrake)

If some of these conditions is not respected, the engine will not work remotely.

Preparation of car

In order to put a car in the protection mode with the Starline autorun function, you need to do the following steps:

1. Stay, Ignition Do not turn off. The engine must be installed. 2. Turn off the transmission, the switch lever must be in a neutral position. 3. Put the car to the "handbrack" - turn on the parking brake 4.

Click on the keychain button 1 and hold it for 3 seconds. You will hear a sound melodic signal. You have 30 seconds to execute the following items. 5. Turn the key by turning off the ignition and get the key from the lock.

The engine does not stall, but will continue to work.

6. Exit the car and make sure that all the doors, the trunk and the hood are closed.

After you close the last open door, trunk or hood, the alarm itself turns off the engine and blocks all the doors - the security mode is enabled.

Only after the successful execution of these steps will be possible the operation of autorun and the engine can be started remotely.

Remote Start

If you correctly prepared a car to autorun (closed the door with the engineered engine, and the alarm was muffled), then you can start the engine with a keychain by any of two ways:

one. Press button 1 and hold it for 3 seconds. or

2. Select the "Start" icon and click 2.

After that, the alarm will make the first attempt to start the engine. In case the engine has not gotten, the second is made, and the starting time of the starter will increase by 0.2 seconds each time. All such attempts will be 4. If the engine does not receive any of the four times, you will hear 4 sound signals from the keyword.

If the engine started successfully, the corresponding icon appears (on different STARLINE models in different ways, usually the exhaust icon), the car is blown 3 times with dimensions and you will hear 3 siren signals.

The car will warm up for a certain period of time, which is specified in the settings. Options - 5, 10, 15, 20 minutes. One minute before the end of the predetermined time, the "R01" appears on the display. When the time is over, the alarm will muffle the engine, and the exhaust gas icon will disappear on the key chain and "R00" will appear.

Top temperature

In winter, many people have the need for a night warming the car so that in the morning there were no problems with the launch. When you turn on the autorun in temperature, you can set the value of the ambient temperature, when the engine is reached, it will start. Temperature values ​​can be programmed as follows: -5, -10, -20, -30.

To enable temperature startup function, select the icon with a thermometer and the launch "START" icon, and click on the key chain 2. In this case, you will hear the ringing sound and the value of the set threatening threshold is highlighted.

To turn off the autorun temperature, select the icon with the thermometer and press the 2 key chain.

If you need to get into the car while warm up the engine (to start moving or just take something from the cabin), click on the key chain 1 - locks are unlocked. Within 30 seconds, insert the key into the ignition lock and turn it by turning on the ignition. If you do not have time to do this, the locks are blocked again and the security mode will turn on. In order to completely exit the autorun mode, lower the "handbrake" - the dimensions are blown 1 time and the sound melody will be heard - you can go.

Now you know how to turn on the motor autorun using Starline alarm. The most common driver's error is that they do not conduct the necessary actions to turn on the autorun and close the muffled car manually with the keychain. I hope now you have no questions left to use the alarm functions.

Replacing the muffler VAZ-2107

Clearance of popular cars

A source: https://vmiredorog.com/sovety-avtoljubiteljam/101-kak-nastroit-avtozapusk-dvigatelya-signalizaciya-starline/

All about car alarm Starline A92 with installation and operation instructions

Page »Alarms» All about car alarm Starline A92 with installation and operation instructions

Car alarm Starline A92 is a domestic security system, the main advantage of which is the remote start of the engine over alarm clinic or temperature. The range of the device can reach 2000 meters, which is very convenient in urban development.

Signal Starline A92 has the following characteristics:

  1. Works at frequencies from 433.05 to 434, 79 MHz. It makes the anti-rone much more secure in comparison with other security systems.
  2. The dialog code from hacking protects the individual key encryption with a length of 128 bits.
  3. The new "jumping frequency" method is used, a significantly complicating process of hacking a signal. The 128-channel narrow transceiver increases the range of key fob. When transmitting commands to the block range - 800 meters, if the transfer comes from the block - 2000 meters. The maximum distance of the second block action is 15 meters.
  4. The temperature in which the security system steadily performs its work, according to the developer, is -40 - +85 degrees.
  5. The voltage of the current is from 9 to 18 mA. Up to 25 mA can come up under security.
  6. Blow sensor - piezoelectric type. Its main advantage is the fixation of any mechanical impact on the vehicle. In addition, it can be operated in conjunction with another security complex, if there is a need for this.

Equipment

As standard, the STARLINE A92 automotive alarm configuration is available:

  • Signal Powerboard;
  • Keychain with double-sided ties and LCD screen;
  • key chain with double-sided communication without a LCD screen;
  • Screen sensor with a two-level system;
  • transceiver;
  • hood button;
  • one LED;
  • Service button;
  • Wiring set for connection;
  • Move temperature sensor;
  • Installation instructions;
  • manual;
  • User memo.

Complete set of automotive alarm Starline A92

Advantages and disadvantages of the system

Of the advantages of the STARLINE A92 signaling, you can allocate:

  • Russian language in keychain, which makes management available;
  • a simple installation process that will not take much time;
  • Large range and significant degree of protection.

Among the deficiencies of the alarm STARLINE A92 mark:

  • excessive sensitivity of individual keys;
  • Responding to random push buttons;
  • The incorrect operation of the security system in a strong frost.

However, according to user reviews, such faults are associated with an incorrectly configured contact, which, in turn, does not pass the signal.

Step-by-step instructions for installing STARLINE A92

Step-by-step instructions for installing a secure complex Starline A92:

  1. The central block is placed in an inaccessible place. The device can be installed under the tidus, the main thing is that it does not fall into it moisture and heat. Fastening is carried out with the help of self-tapping and scotch.
  2. A transceiver module is fixed on the windshield. The antenna is installed so that metal parts of the body, rain and illumination sensors were at least five centimeters at a distance. In a place where there is a toning or sunscreen, it is impossible to position.
  3. Sirena is installed in the cutting space of the car, away from moisture and heat. Place the hover down.
  4. The shock sensor is fixed using a metal screed or scotch.
  5. The temperature sensor is fixed by cable ties on the cooling system nozzle near the engine block.
  6. The LED is installed in the prominent place of the tidy.
  7. The hidden button is mounted in an affordable place so that it does not catch the eye.

Photo Gallery

Purpose Contact Connection Scheme

Operating Instructions Starline A92

In the instruction manual, the process of using and programming various options is fully described using the service button and the timing of car alarm.

The location of the buttons on the key chain to configure the functions.

Overview of the block chagrin Starline A92 and its basic functions is presented in the videos of the author from the channel Alexander Shkurevsky.

How to remotely start the engine?

For remote launch of the power unit, it will be necessary:

  • Automatic transmission to fix in the "P" position;
  • activate "software neutral";
  • close the hood;
  • Put the car on the handbrake.

For remote launch, the engine is necessary:

  1. Select the pictogram with the image of the ventilation and press the "3" button on the key chain.
  2. Click the "1" button until the audio signal appears.
  3. Then press the "3" button.

Setting up autorun.

Automatic Starting Starline A92 makes it possible to set up a start-up auto keychain by:

  • time;
  • temperature;
  • alarm

Setting in time

Step-by-step process of setting up the time engine in time looks like this:

  1. Clamp icon with clock.
  2. Next clicks the "3" key.
  3. The same button adjusts the required autorun time. (If you repeat this combination can be renewed).

To disable this feature, it is necessary to use a combination - 1 (long) and 4.

Temperature setup

This feature provides the ability to choose from already existing temperature modes. Then the time is determined through which it will be activated (the shortest interval is an hour).

This option is configured by pressing the "thermometer" and the "3" buttons. The car will give the light signal with the headlights and the temperature will appear on the key chain at which the autorun will be activated.

Configuring an alarm clock

Instructions for setting up the autorun alarm for alarm clinic:

  1. Click on the image of the clock.
  2. Next, click on the "3" button.
  3. After that, set the right time.

To disable the option, set the cursor to the clock indicator.

The reasons for the impossibility of autorun and ways to eliminate them

The reasons for which autorun may not work may be different:

  1. Incorrect use of the signaling of the owner. For example, late passage of the program neutral procedure.
  2. Cleaning the elements of the security system, such as sensors.
  3. Mounting error.

If an autowner error does not allow you to automatically start the car, you should read the documents that are included with the signaling. There also describes the correct connection of all connectors.

Safety technique

When installing and operating the STARLINE A92 alarm, it is necessary to comply with safety equipment:

  1. The machine should not be indoors without ventilation.
  2. The car should always be on the parking brake. In this case, the box should be in a neutral position or in the "Parking" mode.
  3. Starting the engine must be carried out, making sure that there is no one about the car.
  4. Do not transfer strangers to unauthorized people.
  5. Check all fluids and systems.

Download Installation and Operation Instructions Starline A92 in PDF format

You can download instruction manual and installation by reference below:

Operating and Alarm Manuals in Russian
StarLine 92 Dialog.
StarLine 92 Dialog.
StarLine 92 Dialog Can
StarLine 92 Dialog Can

Alarm overview Starline A92 is presented in the videos of the author from the StarLine2011 channel.

Did you have any questions? Experts and readers of the AUTODVIG website will help you, ask a question to appreciate the benefit of the article: ( 3voice (s), 4.67 out of 5)

A source: https://autodvig.com/alert/starlajn-a92-66911/

How to figure out the Starline alarm. How to configure the STARLINE alarm keychain? Setting time on the keychain

Automotive alarm Starline can be used both with a keychain and using a mobile device. We will analyze the installation of automatic launch and options for configuring this function.

[Hide]

Conditions for installing a STARLINE autorun

To set the automatic switching on the engine of the machine, you must consider the following conditions:

  1. The vehicle ignition system must be disabled. Before closing the doors and setting the car to security, it is necessary to extract the key from the ignition lock and make sure that all indicators and badges were injected on the control panel.
  2. The transmission selector must be switched to a neutral position. It is impossible to allow the lever to be installed on the first, second or other transmission. If it is so, start the engine will not work. For such a start, you will need to squeeze the clutch pedal, and the anti-theft system will not be able to do this.
  3. All cabin doors, luggage compartment and the hood must be locked. The anti-theft system puts the car on protection, provided that everything is closed. Otherwise, security will not be activated.
  4. The car must be put on the handbrake. It is necessary for its reliable fixation on the surface.
  5. If these rules are met, the automatic car owner will be able not only to carry out an automatic start, but also to configure the system so that it triggered at a certain time either under concrete conditions.

Starline autorun installation

The installation procedure of the autorun system is carried out as follows:

  1. First drop the wires in the ignition lock, which are used to start the motor. Implement airbags if they are available. Be careful not to damage the trim on the steering wheel.
  2. Connect the main contacts in the automatic start system to the ignition switch. To connect, the scheme is used in the instruction, it contains all highlights. Depending on the model of the anti-theft system, the electrical power can be different. If the vehicle is equipped with an immobilizer, additionally buy a device to bypass it. This device is an auxiliary module, an additional ignition key will be connected to it. To ensure the start of the power unit, the system will read the data from this key and transmit them directly to the lock.
  3. Then, from the automatic power control device, it is necessary to stretch the wire and connect it to the tachometer or to the generator set. You can connect contact to the motor fluid sensor.
  4. The final step will be programming the autorun module. The procedure is carried out in accordance with the operating instructions for the signaling. Additionally, you need to stretch another cable from the control device to the manual or main brake. This will ensure the possibility of emergency deactivation of alarm.

How to enable and disable autorun

The instruction that comes in a set to the anti-theft system will explain how to use the signaling. Consider an example of using the enabling and shutdown function with the A94 system model.

Michael MNS spoke about the signaling control nuances with the autorun option.

How to enable autorun:

  1. Click on the first button on the remote, hold it until the beep sounds. After triggering, briefly press the 3 key.
  2. Exhibits the cursor on the display of the console on the icon, visually resembling a fan. Press the 3 key again.

A source: https://avtozvuk174.ru/kak-signalizaci-v-signalizaci-pravilno-nastroit/

How does autorun system work?

After stopping the engine, it begins to cool. Until a certain limit, it is not so essential: the car normally starts and no problems in his work arises. But in winter, during severe frosts, the viscosity of the oil is significantly increased. In order to run, the engine is now required more energy that the battery can not give.

In addition, even if the car becomes necessary, the details, no longer lubricated, wears much stronger. To avoid all this, and you need autorun on the temperature of the engine.

This system based on sensor readings (they determine the temperature of the coolant, oil pressure, the battery charge level, and on diesel engines also the operation of the incandescent candles), includes ignition. The motorist has the opportunity to choose yourself, at what temperature it is required to start the engine and to what extent it is necessary to warm it (some types of systems are depleted cars not by the thermometer, but by timer).

After cooling, the device reappears the autorun. At the same time, if the autorun temperature of the engine is installed correctly, the machine can be left unattended for a sufficiently long period.

The automatic start of the engine at a temperature is convenient because the parameter settings are carried out both on the head unit and using the alarm keychain.

How to set the engine start?

For different alarms, the method of installing automatic engine start is different, but, in general, the principle of activation is the same. For example, the StarLine A91 model will be taken.

  1. Before you start, you need to install software mode on the keychain (when the ignition is turned off, press the service button 6 times, then turn on the ignition). Now you can choose the necessary temperature value (which engine temperature to put autorun will be discussed below). To exit the mode, it is enough to drown out cars.
  2. If the car is equipped with a manual transmission, then, to prevent the machine running on the transmission, you will have to implement another procedure ("software neutral"). The car must be put on the handbrake, then the button with the lock icon is clamped on the alarm key chain for 3 seconds. Then the key is removed from the ignition lock (the motor is still running). After another press of the button, the engine will stall, and the car will remain under the alarm.
  3. Now you need to press the button with an asterisk twice. The display should show the temperature (on a well-haired car it will be positive). If the Lo icon appears, it means that the autorun temperature was not selected, or the car cooled to -40 ° C.
  4. Next, you should press the button with an asterisk several times - the keychain will not emit two beeps. At this time on the display, in the lower left corner, the icon flies.
  5. Pressing the same button, you must move to the thermometer icon. Now, if you press the button with the lock icon ("Enable"), the beep sounds, and the system will be activated. Instead of hours, temperature indicators will appear on the display.

For other signaling models, the engine start to temperature can be different. You should not improvise when activated - it can confuse important settings . The instruction should be in the manual attached to the system. It is for him that he needs to follow.

During customization, many people have a question: "What kind of choose the temperature to automatically start the engine?"

What temperature to put autorun?

When setting up the launch system, first of all it is necessary to focus on the capabilities of the car itself. That is, the selected temperature should be such that the car can get started from the first time. It is desirable to prevent such a situation that the device works too often.

For most models of machines, the optimum engine temperature of the engine in winter - 15-20 ° C (for diesel engines - 10-15 ° C). Work time - 10-20 minutes. If there is no possibility to specify it - the car will work until all the indicators approach the usual.

Important! If a weak battery is installed on the car, the optimal temperature of the engine for autorun is not more -10 ° C.

A source: https://avtodvigateli.com/tyuning/sistema-avtozapuska.html

How to configure STARLINE A91 alarm autorun by engine temperature

Auto start Starline A91: Setting the main functions

Although Starline A91 and outdated according to modern concepts (the absence of flexible custom channels, support for CAN / LIN-tires, the use of a radio channel of 433 MHz), "In the Urban" there are still a lot of alarms of this model. And often there are questions about its configuration: for example, how to set up the autorun "Starline A91" in time or set autorun with a keychain. Especially if the car is purchased in the secondary market, and the instruction from the alarm installed on it has long been lost.

What does Starline A91 know in terms of autorun?

  • Arbitrary autorun: can be performed at any time when the car is in the zone of a confident radio reception or an external GSM module is connected to the alarm;
  • Alarfinger autorun: The car will start once at a time that is set in the alarm settings;
  • Auto start "Starline A91" by timer allows the machine to independently warm the engine with a frequency of 2,3,4 or 24 hours from the moment of activation of the mode;
  • It is possible to set up the "Starline A91" temperature so that the engine warming began when the engine temperature drops below the specified threshold, but not more often than once per hour.
Video: Periodic Auto Run mode. Auto alarm STARLINE A91.

Basic autorun settings

To use the STARLINE A91 autorun, it is necessary that the alarm is correctly connected and configured. The main system settings are set as follows:

  1. When the ignition is turned off and the disabled protection quickly press the security button of the security system 6 times.
  2. Without delay, turn on the ignition. The alarm must submit six sound signals, thereby reporting that successfully entered the second menu of settings (autorun settings).
  3. Sequential press of the service button to select the desired function (from 1 to 12). After each press, the alarm will be the siren signals to confirm the number of the selected function, and the short signal of the siren means the unit, and the long-five. That is, four short signals mean that the function 4, long and short - function 6, two long and two short - function 12.
  4. The required value of the selected function is set by the basic keypad with buttons: short-term pressing of the buttons 1.2 and 3 sets this function to the corresponding value by number, long and then the short press of the button 1 sets the function to 4.
  5. After installing all the desired settings, the output from the menu is turned off.

For the user, the following set of functions is relevant (some of them are programmed according to the connection scheme to a specific car, and changing these settings can cause autorun failure):

  • Function 2 Sets the duration of the engine after the forced launch or launch by the algorithm (alarm clock, timer, temperature). In the values ​​of the function 1.2 and 3, the heat dissipation is 10, 20 and 30 minutes. In option 4, the motor will not be faded automatically, each time it will be necessary to join the keychain;
  • Function 3 allows you to warm up to the "Starline A91" on the timer at 2,3,4 and 24 hours;
  • Function 4 configures autorun on Starline A91. In embodiments from 1 to 4 threshold, with a decrease in temperature below which the motor will be launched, respectively, -5, -10, -18 and -25 degrees Celsius;
  • Function 6 Defines the logic of the light indicators during the engine warming (depending on the connection of the alarm to a particular car, it may be turn signals or dimensions). They can burn impulse (option 1), constantly (option 2) or be disabled (3 and 4). Note that when the alarm is connected, it is not directly to the lamps, and to the alarm button turn signals and in version 2 will flash, since the "accident" will continue to be permanently included;
  • Function 9 sets the maximum duration of the scroll of the starter: 0.8, 1.4, 2 or 6 seconds. Note that this maximum duration is relevant only for the indirect determination of the fact of successful launch (alarm is not connected by tachosal). We recommend to leave it in the meaning that was set by the installer;
  • Function 10 sets the delay between the inclusion of ignition and the scrolling of the starter: 2, 5, 10 or 20 seconds. For diesel engines with incandescent candles in winter, it makes sense to set a longer delay;
  • Function 12 Determines how the alarm will enter the ignition support mode, starting the autorun redundancy algorithm. Since the reservation of the autorun is only necessary for cars with manual transmission ("software neutral" need to be guaranteed not to leave the machine on transmission), for vehicles with automatic transmission, it is necessary to set the function 12 to 4 (disabled). Installing this value in 4 on vehicles with manual transmission blocks autorun, it can be used to completely disable Starline A91 autorun. Reservation in Embodiment 1 occurs automatically when the manual brake is tightened at the time of turning off the ignition. Some cars during a pause between the ignition shutdown by the key and the operation of the power relay of the autorun can be sick, in this case, the function must be set to 3 (automatically when the "handler" is tightened). If you do not need automatic backup, set the function to 2 - the backup will occur if you press the button 2 when the engine is running and tightened by the manual brake.

Forced autorun

To enable Starline A91 autorun at any time, use the keychain. Naturally, the machine with the manual transmission must be used to undergo a given procedure "software neutral" and after that not to be removed from the protection.

To start the engine, the button 1 button first is long pressed, after a short scoop - button 3. The display on the screen will be changed to "ST", the car will turn on the ignition and after the time specified by the function 10 in the settings menu, will try to start the motor. With a good launch, the indication is again changed: the "smoke" of the exhaust pipe is drawn on the display, the time remaining left before the engine is degraded. For example, if a function 2 is set to 3 (30 minutes), the display will begin the countdown from "G30" to "G00", after which the motor will be muffled. If the warm-up time is set to "Infinity" (value 4), then the display will indicate the "G99".

Since the Starline A91 autorun setting requires access to the car, it is possible to extend the warming time remotely if necessary. For this, while the motor works, you need to press the same autorun buttons again - first a long button 1, and button 3 after that briefly. The countdown timer will reset to the initial value and again will start counting on the interval, which is set in the settings - for example, if the warm-up time is installed for 10 minutes, and by 9 minutes you extend the warming time, the total motor will work in 19 minutes.

To drown out the motor until automatic shutdown, press the button 2 for a long time, and then button 3 briefly.

Alarm autorun.

A single-time autorun on the alarm clock is not possible if the launch of the timer is also activated, and vice versa. Only one mode set by the latter will be active. That is, for example, if you are set by the autorun every 24 hours, but you additionally installed alarm clock for a while and included autorun on the alarm clock, the following autotype "Starline A91" will occur during the time set on the alarm clock, even if the next launch The timer should be before this moment.

To use alarm autorun, configure:

  • Current time on the screen screen;
  • Starting time.

Both of these operations can be performed simultaneously by entering the keychain settings. Hold a long button 3 until the key chain first long, then one short and two short signals. The clock display on the screen will begin to blink, buttons 1 and 2 will increase and decrease the value. Next, by pressing the button 3, go to the minutes setting, then adjust the alarm.

After setting the alarm time, the next press of the button 3 will switch the key chain to the alarm on and off mode (ON and OFF inscription). Alarm autorun will only work when installed in ON.

Then activate the autorun on the alarm clock itself. He, like other ways of software autorun, is activated through the cursor menu at the bottom of the screen. It turns on it for a long press button 3, but you need to release it after the first short signal. Then with short clicks of the button 3 you need to set the cursor to the desired icon, turn it on with button 1 or turn off the button 2. The icon depicting the alarm is answered for autorun on the alarm clock.

True autorun

The timer autorun turns on and off in the cursor menu keychain using the icon depicting a rotating fan. At the same time, the machine with the manual transmission must pass "software neutral", since after activating the icon automatically, the first autorun will occur, and from this point the intervals specified by the function 3 menu will be counted.

Attention! When using periodic auto-starts by timer and temperature, be sure to make sure that the function 2 is not set to 4!

Top temperature

The temperature of the temperature is turned on in the cursor menu by the "Sigdition" icon. This feature is available if, when installing the alarm, the sensor is connected, which is connected, and this sensor is in charge. After activating the mode, the first autorun will occur at least 1 hour regardless of the engine temperature.

Video: Auto alarm STARLINE A91. Auto start mode.

Autostart faults

If the Starline A91 autorun does not work, make sure that:

  1. On vehicles with manual transmission, the "software neutral" procedure was performed, and the car after that was not removed from the protection (removal of protection disables autorun redundancy). Be sure to burn the indicator of the tightened handbrake.
  2. On the screen screen there is no indication of an open door or a hood (undercooked or defective). Check and troubleshoot.
  3. Being near the car, try to perform forced autorun. If the command is not performed at all (ignition does not turn on), check the connection of power relays of the autorun, the state of the fuses. If the ignition is turned on, the starter works out, but the launch does not occur, check the performance of the immobilizer speaker. If the motor grabs, but the alarm disables the ignition after that, this means that it does not recognize the fact of the launch (does not receive a tachos signal if it is configured to it, or there is no signal level transition from the generator when setting up on the "lamp" - depends on the specific connection and Requires authermal verification).

Startline A91 Alarm Connection Scheme with Automotive

Many security systems have additional options and opportunities that facilitate life to their owner. For example, Starline A91 is autorun. Moreover, it can be installed on any car, including such models as a VAZ 2110 or 2114. The diagram of connecting the car alarm is quite simple and can be carried out in the garage. This will require:

  • Set of a security system;
  • a set of tools including drill, drills, screwdriver, etc.;
  • Soldering supplies: Soldering lamp, solder, tin, rosin;
  • Isol, shrink tubes and industrial hair dryer.

The diagram is shown in the figure below.

For remote motor start, you need to connect a special six-contact connector. In this case, the wires are connected in a certain order.
  • Red cable (+ 12V) goes to the central lock;
  • Yellow (IGN1) - cable for ignition lock;
  • Two black wires are connected to the starter (thick) and ignition lock (thin);
  • Blue and green remain not connected.

How to make autorun with buttons

After the correct installation of the car will be able to hold a remote launch. Additionally, a number of functions for programming will be available. Starline A91 can be configured to autorun on temperature, alarm clock, time or charge of the battery. Below is the video in which it is explained which buttons must be pressed.

Setting the STARLINE A91 alarm on autorun time

The security system has a function of setting the remote start time. This feature allows you to start a motor at a specified hour, as well as warm it to the arrival of the owner. If the first start attempt failed, the next time the starter time is increased by 0.2 seconds. After four unsuccessful attempts on the keychain comes the appropriate alert.

How to set the time of autorun

In order for the function to work correctly, you need to put the correct time on the key chain. After you need to enter the programming mode, by pressing the VALET service button in the cabin six times (when the ignition is turned off). After turning the key to the ON position, the car will publish 6 sound signals.

Now click the service button three more times, turning into the appropriate programming mode. For each pressing the machine reacts the audio signal. After that, within ten seconds, on the keychain, you must press the desired button (the first key - each two hours, the second - three hours, the third - four hours). Confirmation of the procedure will occur independently.

Turning on the STARLINE A91 signaling in time

Time autorun shutdown

If necessary, you can refuse this function. Disconnection occurs as follows:

  • long (to the second signal) button 3 is pressed;
  • The cursor moves to the fan icon;
  • Deactivation of the function is carried out by short-term pressing on the second button. In confirmation of this car, the headlights twice the headlights and emit a signal.

Starting an engine for alarm

You can configure your own start of the engine in the alarm clinic. To do this, you will need to first configure these parameters on the keychain itself. Press button 3 before playing a small melodic signal. After that, the clock parameter on the remote must be filled. Two more short presss allow you to go to setting the alarm settings. The desired values ​​are set by clicking on the keys 1 and 2.

To activate the autorun function, you must consistently press the third and first key (after that the clock icon flashes, the melodious sound will sound, and the car will respond to the flash of the overall signals). Using the buttons 1 or 2, you can set the necessary parameter. Then the third button is pressed again, and after the key one (confirmation of the activation of the alarm clock). Another long pressing of the third button allows you to activate the alarm autorun mode.

Changing the warming time to Starline A91

Depending on the selected settings, the car can warm up 10, 20 or 30 minutes. This parameter is programmed after entering the service mode:

  • Turn off the ignition and press the VALET service button six times in the cabin;
  • turn on the ignition, listen to six sound signals from the car;
  • Two twice the VALET key is clicked;
  • The next click buttons keychain defines the warm-up time (the first key is 10 minutes, the second - 20, third - 30). Confirmation of the command is made automatically, do not press anything enough.

How to enlarge start-up time with STARLINE A91

It happens that the machine does not start in cold conditions, if the starter works around a second (factory settings Starline A91). In this case, you can extend the time of its work. The instruction is as follows:

  • When the ignition is turned off, you must press the Valet service button six times to go to programming mode;
  • After turning the key (ON) the car blinks six times with dimensions. Then you need to press the VALET key for nine times;
  • Pressing any button on the keychain determines the speed of the starter (the first - 0.8 seconds, the second is 1.4 sec., the third is 2.0 seconds). Long plus a short click of the first button - 3.6 seconds.

So that the starter does not twist when the work engine must be connected gray with a red wire on the panel tachometer for automatic stop.

Setting the alarm STARLINE A91 on autorun temperature

  • Turn off the ignition, press the VALET key six times;
  • we turn on the ignition, click Valet four times;
  • Now the first button on the key chain will set the parameter -5 degrees, the second - minus 10, the third is minus 18. Long, and then the short press of the first button is responsible for setting the parameter - 25 degrees Celsius.

How to change the autorun temperature to Starline A91 with a keychain

How to set autorun on the engine temperature keychain

Now the basic parameters are set, it remains only to activate the autorun function by temperature:

  • Press a long key for a long key, up to the second melodic signal, which will play the keychain;
  • Two twice by clicking on the third button so that the cursor on the display moves to the icon with the thermometer;
  • To activate, you must click on the first key once.

Now the car will start with the temperature owner.

Disconnection of autorun temperature

If the owner of the car for a long time leaves or automatic launch at a temperature is not necessary, then this function can be removed. The procedure occurs in the same way:

  • We click the third button for a long time (to the second beep);
  • Two two times click on the third key to briefly to move the cursor to the pictogram of the thermometer;
  • The second button deactivate this feature.

Startline A91 Alarm Operation Manual with Automotive

Why autorun autorun does not work

Sometimes it happens that the autorun function does not work. For example, the starter turns the engine, but it does not start. In this case, it is necessary to check the presence of gasoline in the tank, as well as the charge of the battery. In the first case, everything is clear - it is necessary to add gasoline. In the second - to charge the battery.

It is also possible that the motor does not grab on the cold and even badly start from the key. In this case, you can set the settings at which the starter time will be increased. You can also reduce the interval between start-up attempts.

But the most common reason why the car does not start, becoming banal inattention. Such reasons include the transmission included (for vehicles with automatic transmission

Drive), unlocked door lock, etc. It happens that the car stopped starting because the system badly catches the signal.

In this case, the keychain issues information and immediately writes an error. To reset the protocol, you must start the motor from the key again, tighten the handbrake. Then get the key from the ignition lock, open the driver's door and activate the alarm. Typically, the car again arises to protect, and the OS7 error simply disappears. However, it happens not always. If this did not happen, you must contact the service center.

What if the autorun does not work

It is also necessary to check the console itself. It may be damaged - have cracks on the display, mechanical damage or tritely discharged battery. In this case, the signal is not transmitted remotely, respectively, the remote start does not work. In order to understand how much the key chain is "to blame, you need to configure the launch from the phone (the instruction is described above). If even after that the problem does not disappear, you need to spend thorough diagnosis.

How much is the key chain Starline A91 with auto start

The price of the security system depends on the configuration of the set. For example, in Moscow, car alarm costs from 4 thousand rubles, and if there is a GSM module, the cost increases to 9 thousand. For other cities of Russia, this figure may vary.

City The cost of Starline A91, thousands of rubles
Moscow 4-9
St. Petersburg 4.2-8,8.
Yekaterinburg 4.4-7
Saratov 3.5-6.8.
Volgograd 3.8-7,3

Reviews

Recently took the car, it was already StarLine A91 installed. I will say so - very advanced car alarm for your money. Very good feedback - on the key chain it is immediately clear what is included, although there is a whole bunch of different indicators. And the display itself with good illumination, even on a sunny day does not turn out and remains informative. In general, it suits me completely, I think that this system would put on another car.

Starline A91 chose after long reflection. I say that I did not lose. On your money just excellent alarm. There is everything that can be autorun, feedback and turbo -mer, which is very important to me. Each parameter is configured separately, which is convenient. In the morning I drink coffee, and then I go out and sit down in an already warm car, thanks to the autorun. And it is also cool that you can put the GSM module and manage some features directly from the phone. It is really convenient. Especially for the price in which Starline A91 is estimated.

Starline A91 Operating Instructions

Alarm "Starline A91" uses well-deserved demand from consumers. It triggers at an impressive distance, able to ignore radio interference, simple and reliable in control. Before using this convenient anti-theft instrument, it is necessary to study its main features and functions.

Setting time on keychain

To set the time on the keychain, you must press and hold the button number 3 with the image of the snowflake until the audio signals follow:

  • one melodic;
  • one short;
  • Two more short.

Sound signals are notified by the user that the keychain is ready for time adjustment.

Current time. First set the field "Clock" that flashes on the display. Each pressing button number 1 with an image of a closed lock increases the time for one hour, and each pressing on the button number 2 with the image of the open lock reduces it.

When the "Clock" field is filled, go to setting the "Minute" field. To do this, briefly press the button number 3 (Snowflake) - the "Minutes" field begins to flash. Again, the number 1 button (lock) increases the time for one minute, and with button number 2 (open lock) decrease.

Alarm clock. After the minutes are configured, click on the number 3 button (snowflake) and go to the setting of the alarm readings. When the "Alarm clock" field flashes, again with button number 1 increase the time, and the number 2 is reduced if necessary.

The next short pressing button number 3 (Snowflake) allows you to enable or disable alarm clock. Button # 1 (lock) includes an alarm clock, button # 2 (open lock) turns off it.

Timer. If you press the # 3 button (Snowflake) again, the display will appear for the timer setting. Just like the clock and alarm clock, the timer is adjusted using the buttons number 1 and No. 2.

By pressing the # 3 button again, you can switch to on or disconnect the timer. Button # 1 (lock) Enables the timer, button # 2 (Open lock) turns off it.

Autostart Programming Starline A91

Alarm "Starline A91" allows you to program the autorun of the engine at a temperature, timer or alarm.

Autostat for engine temperature

Press the # 3 button (Snowflake) on the key chain and hold it until one melodious one is swapped, and then one short signal. Then, also by pressing the third button, we move the cursor over the icons located at the bottom of the display until it stops on the icon with the image of the thermometer. Press the number 1 button (lock) - the melodic signal sounds. The system is activated. As soon as the temperature drops below the programmed value, the engine will start for warming up.

In order to disable this feature, you need to press the number 3 button again and hold it to the second sound (melodic sound, then a single signal). After that, with the same third buttons, move the cursor to the icon with the thermometer and press the # 2 button (open lock). A melodic signal keychain notifies the user that the function is disabled.

True autorun

To activate the engine autorun function by timer every 2, 3, 4 or 24 hours we do the following. Press the # 3 button (Snowflake) and hold it until one melodic one is heard, and then one short signal. Then, using the same third button, we move the cursor over the icons located at the bottom of the display until it stops on the icon with the fan image. Press the number 1 button (lock) - the melodic signal sounds. The system is activated.

To disable the timer autorun function, you need to press the # 3 button (snowflake) and hold it to the second sound (melodious sound, then a single signal). Then, using the # 3 button (Snowflake), we move the cursor to the icon with the fan and click on the # 2 button (Open lock). The melodic signaling signal will notify the user that the timer autorun function is deactivated.

Alarm autorun.

First you need to make sure that the clock on the keychain is set correctly, and the alarm is set at the right time.

To activate the motor autorun function, you need to press and hold the no button number 3 (asterisk) until the remote has emit three beeps and the corresponding icon will appear on the display. The display shows the set to start the alarm clinic, which will then change for the current time. The LED indicator will issue signals from two outbreaks.

To turn off the alarm autorun function, you need to re-install the cursor on the icon and click on the key chain # 2 (open lock). After two outbreaks of the dimensions and a melodic signal, the icons will disappear. This feature is activated by one start cycle. To make the next start of the engine on the alarm clinic, you will need to activate this function with the keychain.

Sensitivity sensitivity sensitivity

To configure the sensor sensitivity of the Starline A91 system, you need to perform the following steps:

  • Disconnect the battery terminals (as an alternative - to remove the fuse, which is responsible for the interior lighting);
  • Find a place to attach a shock sensor (as a rule, it is under the front panel, in the steering column area and pedals);
  • Disable security mode, translate to programming mode and use the buttons to make the necessary changes.

The sensitivity level has 10 values ​​(0 - minimum, 10 - maximum). Factory installations suggest protection of 4-5 levels. Setting the sensitivity of the alarm, you need to take into account the level of the car load. The alarm operation should be considered correct in the absence of false positives.

After setting up the system, you need to wait 2-3 minutes, and then turn on and disconnect the alarm several times to make sure its stable operation.

How to "prescribe" keychain

If you lost the keychain or it has failed - do not worry, you can purchase a similar native or compatible instructor in auto shops. The new keychain needs to "register" in the system. For this you need:

  • turn off the ignition of the car;
  • seventerately click on the programming button (VALET);
  • turn on the ignition of the car;
  • Listen to 7 audio signals that warn that the user activated the recording mode of the keychains;
  • Take into the hands of a new keychain, simultaneously press and hold the buttons number 2 (open lock) and No. 3 (Snowflake);
  • After a single siren signal, the buttons can be released.

The new key chain is "registered."

To exit the "Specifications" mode of new key chains, you need to turn off the ignition of the car. In confirmation, overall lights flashed 5 times.

How to disable alarm without a key

Skills for disabling alarm without a keychain will be useful if the remote control is faulty or in it a battery. To deactivate the system, the programming button (VALET) is designed in an inconspicuous, but accessible location of the cabin.

Deactivation without a keychain: if the personal code was not installed:

  • Open the car door with the key, while the alarms are disconnected. If the keychain is not used to activate the alarm system, turning pointers flash 4 times.
  • Include ignition for 20 seconds and click on the service button three times.
  • Ignition turns off. Siren signals twice. Protection mode is disabled. You can start the car.

Deactivation without a keychain: if a personal code was installed:

  • Open the car door key. Alarm signals are triggered, and turning pointers flash 4 times.
  • Turn on the ignition and click on the service button number of times identical to the number of installed personal code.
  • Ignition turns off. Rotary pointers flare 2 times. If the personal code was one digit - the protection mode is turned off. You can start the car.

If there were 2 or 3 digits in the personal code, the user should hold the second and third deactivation in a similar manner.

Reset to factory settings

To reset the Starline A91 alarm settings, use the following algorithm:

  • Include ignition and 10 times in a row click on the service button located in the car;
  • Turn off the ignition, while the siren will publish 10 short signals, notifying the user that it translated the alarm to the settings reset mode;
  • once pressed on the service button, after which one signal of the siren sounds;
  • Press the number 1 button (lock) on the keychain, after which the system with a short one-time signal notifies that factory settings are reset;
  • To exit the settings reset mode, the ignition is translated or waited when the system automatically comes out of this mode. In confirmation, the overall lights flashed five times and the key chain makes a melodic signal.

Everything. Alarm is reset to factory settings.

Thus, the STARLINE A91 signaling can perform automatic functions, and can mechanical adjustable by pressing the buttons. A significant part of its functions change through programming. Therefore, configuring the system can be created a convenient and reliable anti-theft system that will serve you for a long time and trouble-free.

Forum on bus and auto alarm

You can only set the temperature (change it) by entering the startup parameter programming mode. (Two table, line 4, options -5, -10, -18, -25 degrees). Unfortunately, other temperatures are impossible. If you have a diesel, then you need to choose, and if the gasoline motor is not scaled and the oil for the season and the battery with a bright, then -18 (but it is possible and -10 so that for sure). At -5 it will start too often (river fuel), and when setting up -25, it may turn so much that it does not start. But it was supposed to make the installer when installing the system. Therefore, for a start, try to activate the function on the keychain (the machine must be in the zone of the signal to the signal, and if you have a manual box, then it must be performed a software neutral). Prog Neutral: Park, raise the handbrake (the corresponding lamp light up on the panel), pull out the key from the lock (the machine does not slander), open the door and go out (the door configuration must be correct - to light the light of the interior lamp), slaughters the door, press the 1-setting button For protection - the machine must stumble - the procedure is made.

Now how to activate autorun temperature. To start, check whether the temperature launch sensor is correct and where it is set - clichen twice (fast after each other - the type of Tynz-Tintz) button 3 (asterisk). The machine must swop, peer (auto search mode) and draw the temperature on the keychain instead of hours. If the temperature after the ride is plus, then the sensor on the motor. If you write Lo - most likely the sensor is missing or torn off (with a normal sensor, such an inscription means the heat treatment below minus40). If HI writes, then the temperature in the location of the sensor is higher than +70). If everything is fine, then go to activation: 1. We press the 3 button (asterisk) and keep a long time, waiting for the keychain trills and do not leave wait on, while the keychain does not pic it again. After that, the button is released. If everything is done correctly, the edge left icon will flash on the key chain at the bottom of the screen. 2. Now the fast short press pages 3 Move the flashing cursor to the third left position (square with the thermometer symbol). 3. After making sure that the third icon flashes the "ON" button - button 1 keychain (when it is necessary to turn off, you will need to harm 2). If the command is accepted and understood by the signaling, then the melodic signal will be heard on the key chain and the temperature will appear at the place of the clock, when the motor is cooled to which the autorun attempt will occur. 4. I do not press anything about 8-10 seconds, the key chain is picked, the clock will jump again, and the icon (third) will remain dark. 5. The icon is dark - autorun on temperature is active, it became bright - reversed. If when the activation jumped -18 (gasoline) or -10 (diesel, gasoline) - it is not possible to climb anywhere in programming, it can be done only worse - everything is broken - then (after experiments with programming) the car may not be placed at all. In general, go according to the link http://www.ultrastar.ru/attachment/10329/sla91user.pdf and download the user manual, there is not unpleasant and installation instructions.

Added after 1 hour 19 minutes

If in clause 1. It will not blink and blink, which means they pressed the third button once or with a large gap between the presses - in this case (with one press) will show the temperature in the cabin.

How to set up autorun on StarLine A91

Despite the fact that Starline A91 alarms from the class of budget models of security systems, it meets all the requirements of protection of this kind of devices. It has a data stream of 8 floating channels with a 128-bit encryption code with an intelligent autorun function. This complicates the interception of the signal, since the system itself, with each "keychain-car" dialogue, automatically selects the radio frequency that in urban conditions with radio cells has an important meaning.

How to start the car from the block

It is known that the STARLINE A91 security system has a motor autorun. But before this it is necessary to perform a number of mandatory actions:

  1. Transfer the PPC knob to the neutral position (turn off all transmissions);
  2. Turn off the ignition and pull out the key from it (the engine must be included);
  3. Activate parking brake.
  4. Tightly slam all the doors, as well as the hood and lid of the trunk;

If some stage is missing, the remote start is not possible. But with proper preparation of the machine (the motor is dried by the warning itself), it can be started with a remote option.

    Press and hold three seconds button number 1 and after the audio signal quickly press the button number 3:

Or periodic engine start from keychain:

This feature is especially relevant in the winter when periodic engine heating is required. The StarLine A91 key chain can automatically run the engine for heating (after 2, 3, 4, 24 hours).

How to set up autorun time, temperature

Starline A91 Dialog Alarm is allowed to configure this manner that it will automatically start the engine at air temperature (usually minus) or after a specific time interval.

Activate the autorun mode for temperature

This function will work when complying with certain conditions:

  • in the presence of a temperature sensor;
  • from the place of its installation;
  • Feed the sensor itself.

It is activated by long pressing the button 3 (asterisk) until the sound signal appears from the key fob - it should be fun once. The display will be blinking the extremely left icon (1) at the bottom of the screen. Short presses on the 3 button moving around the menu to the third left position (square 3) with a thermometer symbol.

After you were convinced that the desired function is activated, press the button number 1 on the housing to activate this mode (this mode is turned off by pressing the button 2 on the housing), and at the point of readings of the clock, the critical value of the motor temperature after which its autorun will appear.

After the temperature value was highlighted, it is not necessary to feed anything - after 8-10 seconds, the remote key itself is picked and the clock will again appear on the display, and the third icon (with a thermometer) will remain dark. According to this icon, it shows whether the autorun mode is started at a temperature: dark - mode is active, light - reset.

Time autorun

To enable this feature, you need to select the display icon 2 on the display. The machine is blinking by the headlights, and the melodic signal will be distributed on the keychain. Now through the time set by the owner, the signaling itself will periodically launch the engine.

If, after the first attempt, the car did not start, the second will follow. At the same time, the starter scroll time will be increased by 0.2 seconds. The timer is designed for 4 attempts to start the engine. If, after the fourth attempt, the engine did not start, triggered a beep on the keychain. To configure the engine heating in time, the sequence of actions is such:

  • Press and holds a long button number 3 on a key chain (asterisk).
  • The keychain will briefly picnet, but the button is pressed, after the second audio signal, release the button;
  • Fits the extreme left icon (1) on the panel;
  • Shortly pressing button number 3, move to the fan icon;
  • One short press of the button number 1 - the keychain will play melody;
  • To wait ten seconds until the key chain is spinning, and the icon with the fan will remain darkened;
  • The interval function is activated.
  • It turns off in the same way, but the choice is confirmed by the # 2 button (open lock) When the engine is successful, the exhaust gases appears on the screen. The car itself is 3 times blocked by the headlights and give a beep three times.

    The reasons for which autorun does not work and how to eliminate them

    Autostart from the StarLine A91 console may well break through the operation. Most often, the reason should be sought not in outdated details, but in improper operation of the system or its installation. If autorun does not work, there may also be problems with incorrect software configuration.

    The most frequent prerequisites for breakdowns

    • The shock sensor does not work. A migration of the shock sensor itself can help.
    • Too frequent alarm operation. There are probable reasons for two. Or too sensitive settings, or corrosion on the connections.
    • No response from keychain commands. If there is no response from the machine to the commands supplied from the control keychain - the controls of the control button or the village of the battery. It may be necessary to fully replace the key chain with a new propelle in the system.
  • Doors of the machine are not closed off the console. Master in service centers can help to cope with the problem. It is necessary to check and determine which places of breaks in the chains between the main unit and the door, compliance with the technical requirements of the actuators and how the door closing pulse is programmed.
  • Autostart stopped working. Most often, the reason lies in a faulty wiring. It may be damaged. The immobilizer commander is also incorrectly delivered (most likely the antenna itself). You must also check the device programming.
  • Car siren does not work. Feed or siren itself, or there was a break in the wiring. Eliminate the problem will help the full replacement of the siren itself or the monitoring of the wiring of the entire system.
  • Automatic Engine Starts - Starline A91 Dialog Operating Instructions

    Page 64.

    User's manual

    Automatic start of the engine for alarm clinic (activated with a keychain)

    · To enable the automatic engine start function to set the alarm on the alarm, first check the installation time on the keychain. Then program the alarm clock by the descriptive engine start time and turn on the alarm clock (see p.18-19). Connected an alarm mode on the display keychain is indicated by icon

    After checking the current time and setting the alarm to serial the buttons 3 and 1 keychain, set the cursor to the icon

    Alarm autorun (see page 20). Follows 1 outbreak of dimensions. The melodic beep sounds and the display will appear on its display.

    indicating together with icon

    Alarm autorun. For a short time on the display of the keychain, the last time of the future startup, which will then change to the current time. The LED indicator will flash a series of 2 flashes. · To turn off the autorun function on the alarm, re-installers on the icon

    And click 2 keychain. Follow 2 flashes

    Gabarites. A melodic signal keychain, icons

    Note one). The presence of a keychain in the zone of the receiving transmitter at the moment of the autorun of the engine on the alarm clock is not required.2). The engine start time may differ from the configuration of the alarm clock within 1 minute.3). The autorun function is turned on by one start cycle. For a new start, each time you need to activate the function with the keychain.

    Automatic launch of the engine by timer (activated with the keychain)

    · To enable automatic engine launch function by timerhouse 2, 3, 4, 24 hours (Programmable function 2.3) Selecting buttons 3 and 1 keyword Set the cursor to the icon

    Taimier autorun (see page 20). Follows 1 outbreak of dimensions. The melodic signal keychain seems. On the display keychain display icon

    indicating the included timer autorun mode. LED

    The indicator will flash a series of 2 outbreaks. Simultaneously with the inclusion

    How to configure STARLINE A91 alarm autorun by engine temperature

    1. How to turn on autorun
    2. How to program
    3. Autostat for engine temperature
    4. True autorun
    5. Alarm autorun.
    6. How to increase autorun time
    7. Sensitivity sensitivity sensitivity
    8. How to disable the function

    The functions of automotive security complexes include the mode of remote or automatic start of the power unit, allowing to warm the motor in the winter. Autorun Starline A91 Allows you to turn on the engine depending on the ambient temperature or at a specified time. The user activates the service and adjusts the mode of operation using the remote control.

    How to turn on autorun

    The autorun enabling implies the pre-installation of the temperature sensor, which is installed on the engine cylinder block or on the coolant supply highways. A contact is used to switch the sensor, equipped with an orange-black insulation cable (part of the 18-pin block of the alarm processor block). To ensure the operation of the automatic power on function, you need to configure the equipment.

    The design of the 18-pin connector is provided with a loop cable equipped with a black insulator. When installing the product on a car equipped with a manual transmission, you need to break the chain. On machines with automatic transmission, you must save the circuit in a closed state. The automatic start algorithm provides 4 scrolling of the shaft starter, the adjustment of the number of starts is not provided. Each subsequent start attempt is distinguished by an increase in the operation time of the starter (by 0.2 seconds).

    How to program

    To change the parameters, find the settings button and click on it, and then turn on the ignition. The system will give 6 signal signals, confirming the readiness for programming. Configure the autorun alarm STARLINE can be in accordance with the setup tables shown in the instructions.

    To select a function, use the impact on the hidden setting key (from 1 to 12 times). Then the owner presses the buttons located on the remote control, selecting the desired mode value (for example, the threshold value of the temperature or the time of operation of the engine for the warming cycle). After that, the user includes an alarm time of the starter, depending on the type of engine and its technical condition.

    When using an automatic start-up on a diesel engine, it is necessary to provide a delay between the inclusion of electrical circuits and the activation of the starter. The time interval is required to warm up the incandescent candles located in the head of the block. Heated metal elements increase the air temperature, facilitating the startup procedure. The complex allows you to select time from values ​​5, 10 and 20 seconds. Basic delay 2 seconds is designed for gasoline engine.

    It is then configured to control the operation of the power unit necessary for the timely disconnection of the starter. The design of the security complex allows you to determine the operation of the power plant by the voltage value in the on-board network, by the presence of a signal in a positive or negative generator chain and by signal transmitted by the tachometer.

    Additionally, the ignition support function is adjusted, ensuring the safe operation of the engine in the absence of the owner in the cabin.

    If the car is equipped with a special button for starting and stopping the engine, it is necessary to adjust the power output algorithm (signal on the blue cable, coming from the 6-pin harness). The final programming and the choice of the automatic power on the engine is performed by 3 buttons on the remote control, which are designated by the lock icons (with a fastened and open handage) and an asterisk. Before installing an automatic start, you should go through the system neutral installation cycle (you need for machines with manual gearbox).

    After configuration, you must check the correctness of the starting system. To test, you need to turn on the ignition, and then click on the button with the star icon. The screen includes a key icon (on the background of the windshield). An additional test is carried out when the engine is running: after pressing the same key, the display is additionally displayed on the display, simulating the exhaust flow. In the absence of icons or displaying other icons, you must check the security complex setting (in accordance with the instructions).

    Autostat for engine temperature

    Adjusting the alarm Starline to start the engine at a temperature involves setting up the central unit on the temperature threshold value. The parameter is selected from the row -5 °, -10 °, -18 ° and -25 ° C. When the sensor is cooled below the programmed value, the crankshaft is scrolled by the starter and the warming of the aggregate. To start it is allowed to use the sensor located in the engine compartment and the sensor located in the car.

    The minimum time interval between repeated launches is 1 hour. The time spent on the heating of the motor is not taken into account. The user cannot change the repeat frequency, since the parameter is determined by external temperature conditions. Installation of autorun on temperature does not provide restrictions on the number of repeated heating (depends only on the resource of the car battery).

    To activate the service, you will need to press the key marked with an asterisk. After serving the melodies and series of 3 short beeps, the programming method cursory is included. The user moves the cursor with short-influences to the button with an asterisk, after selecting the icon with the thermometer icon, you need to change the function value. To activate, you need to press the key with a locked lock symbol. When the start-up on temperature is activated by parallel modes (for alarm clock or timer).

    The keychain will give a melodic signal, accompanied by an outbreak of alarm lamps or dimensions (depends on the method of installing a security complex). On the control panel screen, the active function icon is displayed and the threshold temperature value is shown briefly, in which an attempt is made to start the power unit. The control diode alarm will flash the series consisting of 3 short flashes, confirming the readiness of the system.

    If the further use of the function is not assumed, you need to disable the service. To configure, you will need to enter the adjustment menu, select the cursor using the active icon, and then press the key marked with a lock with an open hand. The car will work 2 times the lights of the alarm, the key ring will lose the melody, which confirms the abolition of automatic warming of the motor.

    True autorun

    Before programming the engine start on timer, you must set the repetition time (from the row 2, 3, 4 or 24 hours). The function is configured through the programming menu of the StarLine A91 signaling processor. The timer autorun is activated through the menu, to enter the settings, you will need to press and hold the button with the icon. The cursor is then translated into the icon with a rotating impeller, pressing the button with the closed lock allows you to enable the function.

    The control diode installed in the car goes into operation of a series of 2 short signals. The motor starts and warms up, the subsequent starts are executed in accordance with the programmed repeat time. The function is turned off through the on-screen menu, after selecting the active icon, you should briefly press the open lock key. Feeding a melodic signal and dual alarm response confirms the cancellation of the program.

    Alarm autorun.

    Before activating autorun an alarm clinic, the user needs to set the current time on the control panel. To adjust, you need to press the button marked with an asterisk, and hold to the melodic signal and the series of 3 short sounds. After the clock field on the display begins to flash, the user adjusts the value (buttons marked by the pictograms of the locked and open lock). To go to setting the minutes, you should briefly press the key with an asterisk.

    To adjust the alarm on the key chain, it is required immediately after setting the clock again to press the button with an asterisk. To configure the inclusion time, the same buttons apply, click on which should be briefly. Prolonged impact allows you to set the value in accelerated mode. The user then presses the button with an asterisk once again and adjusts the minutes. To start the alarm clock, you will need to once again press the button with an asterisk and select the "Enabled" parameter.

    Then it is necessary to press the key to the key with an asterisk (until the length of the long and short signal). Shortly pressing the button should set the cursor on the functions of the alarm clock. To confirm the selection, a button with a closed lock icon is pressed. Emergency light alarm will work, the console buzzer will give 2 short beeps and will lose the melody. The design of the security complex does not allow simultaneous use of an automatic start-up of alarm clock and timer.

    The icon of the active function will be highlighted with dark color (together with an active alarm icon), an additional time for a few seconds is displayed for a few seconds.

    The autorun function in time does not require the location of the control in the signal reception area. The programmable service is one-time, after turning on and warm up the power unit, the mode is turned off. To re-launch, it will be necessary to conduct a new adjustment in accordance with the algorithm outlined above.

    How to increase autorun time

    The user can extend the operation of the power unit only subject to the location of the control panel at the signal reception distance. To add time, you will need to click on a 2-3 second button marked with a locked lock icon, and then briefly affect the key with an asterisk. The help console bundle will give a melodic signal, light alarm lamps on the car will work 1 time. Each impact on the keys allows you to increase the warm-up time for 5 minutes; The remaining value is briefly displayed on the display.

    If the user has raised heating, but then decided not to use the car, you can use the power off function at a distance. To join the engine, you will need to long press the button with the open lock symbol, and then briefly affect the key with the star icon. On the car 4 times the external light alarm will work, the power unit will turn off. The remote display turns out the control indicators that signal the engine warming up, and then the buzzer will fulfill the musical melody.

    Sensitivity sensitivity sensitivity

    The security complex includes a sensor that determines the strength of the strike applied by the body. The sensor is used to turn on the alarm mode, perceiving the blow as an attempt to unauthorized access to the interior of the car. The device is mounted inside the vehicle cabin, the instruction manual recommends placing the product open to adjust the sensitivity. On the case there are control diodes, which are included when fixing the strike of the car body.

    Vibrations occurring during the operation of the engine are perceived by the sensor as a hacking attempt, which leads to the triggering of the siren. To configure sensitivity, 2 potentiometers (warning zone and alarm level) are used that rotate the screwdriver sting. The regulator has 10 positions, when delivered from the factory, it is set to position 4 or 5. Before the start, it is necessary to reduce the sensitivity of the device, turning the regulators to a minimum.

    Then begin to establish a warning level. To adjust, you need to open the car door, activate the security mode, and then rotate the screw of the regulator clockwise. Sensitivity is determined by light palm strikes that are applied on the body. Then the user can configure the Starline alarming level (by analogy). After the adjustment is completed, it is recommended to put the security complex on the autorun and check the sensor sensitivity during the operation of the motor and when you hit the body (paton the roof panel).

    How to disable the function

    The user can turn off the automatic start using the buttons on the control panel. It is impossible to completely disable the function, since the motor operation algorithms are laid in the software of the central unit. If there are problems with automatic startup, it is recommended to forcibly reset the alarm settings, and then program the parameters again.

    How to set up autorun Starline A91

    How to install and configure auto alarm Starline A91 with autorun?

    The Starlain A91 security complex consists of a controller, a transceiver, siren, a shock sensor, a LED indicator, the VALET buttons and a motor temperature sensor.

    Manufacturer Starline 91 provides vehicle owners with typical installation schemes of the security complex on the car. The system installation algorithm is valid for most models of machines found on public roads. When installing the alarm on the elderly, only a minor modification of the proposed installation techniques is required.

    The central control unit connector has 18 pins connected on the next way:

    • Earth or contact with the mass is carried out by black cable;
    • The compound with the overall lights of the car is provided through the yellow-green or black and green wire;
    • To connect the nutritional sirens of the machine, a gray cable is used;
    • To connect terminivists located in the scratched cavities of the body - black and blue;
    • Connecting the end of the hood, the temperature sensor under the cover of the engine compartment is used by the gray-orange wire;
    • For trunking trunk - white-orange;
    • The connection with the minus of the immobilizer crossover uses the pink color wire;
    • The generator relay, implanted in the complex, and is responsible for the functioning of the power unit of the power unit, it is powered through a black and gray cable;
    • The connection of the system with a parking brake provides purple-orange.

    In addition to the designated connections when connecting the complex and configuring its correct operation, the installer may encounter a black cable signaling control unit located on the connector of the black cable alarm.

    This loop has a value when installing a complex on a car with a manual transmission. In this case, it should be cut. If the installation takes place on a car with automatic transmission, the loop remains untouched.

    Function programming instructions

    Security and service functions of the STARLINE A91 car alarm can be reconfigured by exposure to the service key of the currency and the main keyfob buttons without interference with the system controller.

    The list of system service functions includes:

    • Manual functionality of the shock exposure sensor;
    • Management of the functionality of additional executive devices of the system;
    • Lock control and unlocking vehicle doors;
    • Activation of the "Search" state of the car in the parking lot and control the temperature of the cooling fluid of the motor;
    • Service of the complex and modes of its work VALET;
    • Call from the car's salon;
    • Blocking keys of the main and additional communicators;
    • Monitoring the state of peripheral vehicle systems and intra-alone temperature;
    • Registration of new and tracking the number of existing control panels of the security complex.

    Table: Programming Start Parameters

    Configuring autorun is performed according to certain parameters.

    Changeable value. 1 Click on Sensor No. 1. 1 Click on button number 2. 1 Click on button number 3. Long. Then brief effect on sensor No. 1.
    1 beep. 2 beep. 3 beep. 4 Gudka.
    one. The duration of the turbotimer. 1 minute. 2 minutes. 3 minutes. 4 minutes.
    2. The duration of the operation of the motor after starting at a distance. 10 minutes. 20 minutes. 30 minutes. No limit.
    3. Motor launches on timer. 2 hours. 3 hours. 4 hours. 24 hours.
    four. Motor autorun temperature. -5ºС -10ºС -18ºС -25ºС
    five. Motor start state. Protection is active. Protection is not active. Protection is not active. Protection is not active.
    6. The mode of operation of light alerts with a running motor. Glimpses. Included. Disabled. Disabled.
    7. Locking doors when stopping the power unit, protection is active. Disabled. Works. Works. Works.
    8. Sequence of the output function. Double accessories. Spark plug. Becameless access. 1 signal.
    nine. Period of starter function. 0.8 seconds. 1.4 seconds. 2 seconds. 6 seconds.
    ten. By variety of fuel. Gasoline with a pause 2 seconds. Diesel with a pause 5 seconds. Diesel with a pause of 10 seconds. Diesel with a pause of 20 seconds.
    eleven. Control of motor function. On the voltage network. On the positive conclusion. For minus conclusion. By revolutions.
    12. Help the ignition system on the launched motor. By default, the ignition is disabled. From the console. When you turn on the parking brake. Does not work.

    Recommendations when using and general autorun rules

    Starlaine A91 automotive security complex has the ability to automatically start the power unit. In order to make it necessary to pre-perform some procedures:

    • Establish a gearbox selector into a neutral position;
    • Extract the key from the ignition lock;
    • Enable manual brake system;
    • Close the doors, the motor compartment cover and the lid of the luggage compartment.

    How to install

    You can set the remote start of the power unit using an additional six-contact connector. The wiring is connected by the algorithm:

    • The wire of the red is connected to the central lock of the car;
    • Yellow wire to the ignition lock;
    • Two black cables are connected to the starter (larger cross section) and to the ignition lock;
    • Blue and green wires are isolated, remaining free.

    Table: How to enable and disable

    How to setup

    The start of the car's power unit, equipped with STLINLINA A91 alarm with autorun, is possible at the following positions:

    • Command signal from the control keychain;
    • By period of time;
    • In terms of ambient temperature.

    Table: Time autorun setting instructions

    What to do. System response. Charm answer.
    Automatic launch of the timer unit.
    Long press of sensor No. 3 before receiving acoustic alert. The alarm LED blinks with three outbreaks with a period. Two sound alerts will arrive at the remote. Long and brief.
    Sensor number 3 is released from holding. No answer. Flink the bottom row icons on the communicator display.
     The first and third key cursor is summarized to the icon:
    Table of selection of periodicity
    Period. Step. Act.
    one. 2. Click on the first button.
    2. 3. Click on the second button.
    3. four. Click on the third key.
    four. 24. Twice (long and briefly) click on the first key.

    By temperature

    The automatic start of the power unit in terms of temperature is possible when the corresponding sensor is connected, which is connected. After activating the function, the first launch is possible at least an hour after switching on.

    Table: Settings Instructions
    What to do. The answer is the complex. Answer keychain.
    Automatic start of the aggregate temperature.
    Prolonged keystroke number 3 before receiving acoustic alert. The LED system blockers on three outbreaks with a period. Two sound alerts will arrive at the remote. Long and brief.
    Key number 3 is released from holding. No answer. On the display in the bottom row highlighted icon .
     The third sensor cursor is summarized to the icon:
    Table: Launch temperature selection
    • Turn off the ignition, press the currency key six times;
    • Turn on the ignition and click on the service key even four times.
    Period. Step. Act.
    one. -5ºС. Click on the first key.
    2. -10ºС. Click on the second key.
    3. -18ºС. Click on the third key.
    four. -25ºС Twice (long and briefly) click on the first key.
    Table: selection of work time

    With the service button, enter the warming time setting mode, then set the desired parameter value:

    Period. Step. Act.
    one. 10 minutes. Click on the first key.
    2. 20 minutes Click on the second key.
    3. 30 minutes Click on the third key.
    four. Without restriction. Twice (long and briefly) click on the first key.

    On alarm clock

    In order to configure the complex on the ability to start the engine for the alarm settings, you need to set the correct time to the key chain. How to set up time becomes clear from the table below:

    Table: Clock Setup
    Table: Strong programming
    Parameter. Activation. Act. Feedback on display.
    Setting time (clock). Button number 3 is pressed briefly until the icon appears on the screen The values ​​of the sensor No. 1 increase are reduced by sensor No. 2. Alarm clock flash on display:
    Table: Activation and Deactivation of Alarm Autorun
    Act. Information from the complex. Information from keychain.
    Activation of motor autorun by alarm value.
    The button number 3 is kept long. Diode blinks two outbreaks through the period. Accompical alert from a long and short signal.
    The button is released. The pictogram flashes on the screen:
     button number 3 cursor to the icon

    Why may not work and how to fix it

    If suddenly in the car, the security complex began to see, do not panic. The harder the electronic assistant, the more inclined to accumulate the controller in the memory of a different nature of digital garbage. For the most part, the signaling problem can be solved by dropping minutes by twenty, one or both terminals from the battery. When re-applying the power to the security system control unit, the controller is restarted in an emergency mode, resetting the memory storage devices and testing the periphery. If the battery disabling does not bring the desired results, you need:

    • Change the battery in the control panel;
    • Check the contacts of the electrical components of the system;
    • Disable and turn on the complex again;
    • Reflect whether there are no shielded obstacles to the passage of signals;
    • Contact your profile.

    Starline A91 and autorun implementation

    The STARLINE model of the A91 model is in two versions: StarLine A91 Dialog, as well as A91 4 × 4. The first of them is released so far, and all the differences, oddly enough, consist in the form of a key fob and in icons on its display. Connection diagrams of the first and second signaling are no different. There are no differences and in configuration methods. The second model will be called this: Starline Twage A91. And it will be considered that which typical errors are allowed trying to implement autoruns with the specified signaling. The absence of either the low reliability of engine operation control is the main error that can cause severe consequences in reality.

    Methods for monitoring the operation of the DVS

    Suppose, the "black and gray" wire from the main 18-pin connector was connected to the output of the tip or to the battery charge lamp:

    Here you see customizable functions that are responsible for automatic launch. The table is copied from the installation instructions. By the way, do not look for it in the instruction manual.

    We assume that the connection and configuration are made. Check that the automatic start terminal bar (6 wires) is connected according to the instructions. Next, you need to disable the security mode to perform the following check:

    1. The key is translated to the ignition label, the starter starts are not performed, the key 3 is pressed on the keychain;
    2. By starting the engine, a button 3 press button on the keychain and control the display state.

    As stated in the instructions, in the first case, the display must display the key icon. In the second, the image of smoke is added to it:

    The STARLINE TWAGE A91 keychain displays the icons shown below.

    Perform work on errors

    In theory, any car alarms listed here has properties. The presence or absence of difficulties in the setting is due to the car schemes, and not the malfunction in the security system. Starline, however, supplied the user with instructions on how to solve the problems arising. For example, such an effect can be observed: at a low temperature, the launch is carried out "times", and there are no problems in the warm season. So, most likely, control "on the charge lamp" is used, and the voltage at the generator output appears too early.

    Change the sensitivity of the control scheme would be meaningless, and in the 36 line signal this option is not provided. Use another method, for example, the test batch.

    If you can configure control over the generator, you can also not always, then the question arises, is it not easier to control only the voltage. Do not follow the programming of the function 11, and get this option immediately. And then try to perform the verification procedure. In almost every modern car, it will fail.

    There is a advice that does not lead in any instructions or in reviews. By connecting the "black and gray" wire to the charge lamp, try to use both options for setting - 2 or 3. If it does not help, connect to another lamp contact. But the best method, as the Starline experts themselves say is reading the engine tip signal.

    To implement such an option, the control cord is connected to the high-voltage tachometer terminal. You can use the output control, if we are talking about injectionboxes. Then adjust the sensitivity of the signal input, and more this operation is considered in the following chapters.

    In the function of more complex systems that do not belong to the family of the Star Line dialogue include control of the operation of the engine on the oil pressure sensor. The method perfectly works only with some engines, and low temperatures it gives failures. Use exactly the method of control that is reliable during operation in different conditions.

    Connection features, setup

    Consider the scheme that the StarLine A91 Dialog system is installed.

    See where the voltage appears when you click on the pedal. Take into account that when you assume the error, everyone will have to be disconnected - use the coupler.

    Programming function 8 is allowed to be performed both before and after connecting the cord in the "blue" insulation.

    It remains to consider that it is necessary to program that the "pink" signal cord is correctly controlled by a cross-country. There are options responsible for the "behavior" of the StarLine A91 Dialog system during its operation. There are no such settings among them. Well, the functions responsible for autorun, also do not contain anything like this. The algorithm of the work of the manager will always be one. As we considered the necessary experts old line.

    In fact, it is better to check whether the cord is connected correctly in purple-orange isolation. When operating the autorun, you need to activate the "handler", and the specified wire reads the signal just from the brake microcopters.

    Connect the crossover will be easy. But the Instructions of the Star Line does not say the following:

    1. Despite the dialogue regime, it is easier to sobally a car with a correctly installed by the crawl than without it;
    2. The attacker will turn off the immobilizer, simply by clinging the cord on the ground, and there is no problems with hacking locks today;
    3. As soon as the autorun is implemented, due to the increased probability of hacking, the cost of CASCO will immediately increase.

    Everyone who needs autorun, with the presence of a side speaker will have to accept. Full car "guard" is too primitive to understand commands from external devices. So you have to connect bypass, in the absence of which the remote or automatic launch does not work.

    Setting the alarm from zero

    To change the values ​​of the functions listed in Chapter 1, you need to perform the following:

    1. Let the automotive security system be in "removed from protection" mode. Ignition should be turned off, and then 6 times press the Valet service button. In each system of Ultra Star, this element is present.
    2. Turn on the ignition without running the engine. 6 siren signals should be sounded if the latter was connected. Usually during operation, siren is turned off.
    3. Change the number of the option is customizable at the moment, can be single-click on the button.

    To exit the programming mode, you need to turn off the ignition or do nothing more than 9 seconds. Change the value of the function by pressing the key fob key. For the StarLine A91 signal Dialog, the instruction is fully suited, and there are no differences for the twnet version.

    Note: You can configure the start, but not shutting down the operating engine by temperature.

    The main key chain STARLINE A91 looks like this:

    To set a value equal to 4th, button 1 is pressed for a long time, and then briefly. When operating, this option is also used - it allows you to enable protection without a sound signal. For STARLINE TWAGE A91 systems, there will be no fundamental differences: there the keychain is also endowed with three buttons. Reset settings are performed as follows:

    1. Instead of 6 pressures use 10;
    2. After 10 audible signals, the VALET button is pressed;
    3. After a single short-term "bipa", you pick the key 1 on the keychain.

    If the control is used by the touchscreen, configure the sensitivity of the programmable input. The procedure is called "learning", the truth is not used in the instructions.

    You can only view the values ​​of each function on the disclosure of the keyfoot that runs in the dialog mode. It will not be necessary to change these values.

    Teach the STARLINE A91 Dialog signaling to recognize idle turns in reality is not easy. You must first turn off the "yellow" wire connected to the "15" terminal, and before the start of operation, everyone is returned to the same mind. When the cord is disabled, perform actions:

    1. Close the doors, hood, trunk;
    2. "The handbrake" deactivate;
    3. Perform the engine launch;
    4. The motor should work at idle;
    5. Sensitivity will be configured automatically.

    The StarLine A91 Dialog system is also provided with the VALET button, and the LED indicator. If learning is successful, the diode flashes. In any review, of course, do not talk about the difficulties considered here. And the instruction contains the following short text.

    What you need to know the owner

    Starline A91 Dialog alarm can be configured both on the table and the cursor method. Configuring autorun on temperature, go to the "Thermometer" symbol, but if the sensor is faulty, the icon is not activated.

    Such functions could not be implemented if the dialogue mode was not used. In each review, where the Security Complex Starline A91 Dialog is considered, praise and resistance to hacking. All of these characteristics, as can be understood, are related to the presence of a dialogue mode.

    There is a review, where the range of communication with the keychain was measured during testing. When operating, it is obviously several other values ​​other than "passport" are obtained. For the STARLINE A91 Dialog signaling, the following results were obtained:

    The command filed by the system from the key fob was just started starter. Characteristics here look good, but to several kilometers specified in the documentation, they obviously do not reach.

    In responses published by the owners, report information inaccessible in any review:

    • Using the mode dialog entails and negative consequences - the battery is quickly discharged in the display with the display. This effect itself is stronger at low air temperature.
    • The automotive security system of the model under consideration has its own specific disadvantages. After several seasons of operation, for example, you have to configure the shock sensor, turn it off or replace it new.
    • Automotive temperature can be used. But the thermal sensor is better to fasten under the torpedo, and not on the engine crankcase.

    Information from the list may refer to the StarLine A91 Dialog signaling, but not only to it. Ultimately, its processor program provides 3 autorun modes: in temperature, and at certain times (alarm clock) or by timer. Combined mode can be used too. Select the choice for the future owner.

    Auto start in the STARLINE A91 Dialog signaling: Connection, Setup, Tips

    How to change the start of the engine starts Starline A91

    The STARLINE model of the A91 model is in two versions: StarLine A91 Dialog, as well as A91 4 × 4. The first of them is released so far, and all the differences, oddly enough, consist in the form of a key fob and in icons on its display. Connection diagrams of the first and second signaling are no different. There are no differences and in configuration methods.

    The second model will be called this: Starline Twage A91. And it will be considered that which typical errors are allowed trying to implement autoruns with the specified signaling. The absence of either the low reliability of engine operation control is the main error that can cause severe consequences in reality.

    Methods for monitoring the operation of the DVS

    Suppose, the "black and gray" wire from the main 18-pin connector was connected to the output of the tip or to the battery charge lamp:

    Automotive Options, model A92

    Here you see customizable functions that are responsible for automatic launch. The table is copied from the installation instructions. By the way, do not look for it in the instruction manual.

    We assume that the connection and configuration are made. Check that the automatic start terminal bar (6 wires) is connected according to the instructions. Next, you need to disable the security mode to perform the following check:

    1. The key is translated to the ignition label, the starter starts are not performed, the key 3 is pressed on the keychain;
    2. By starting the engine, a button 3 press button on the keychain and control the display state.

    As stated in the instructions, in the first case, the display must display the key icon. In the second, the image of smoke is added to it:

    Checking the operation of the engine

    The STARLINE TWAGE A91 keychain displays the icons shown below.

    Perform work on errors

    In theory, any car alarms listed here has properties. The presence or absence of difficulties in the setting is due to the car schemes, and not the malfunction in the security system.

    Starline, however, supplied the user with instructions on how to solve the problems arising. For example, such an effect can be observed: at a low temperature, the launch is carried out "times", and there are no problems in the warm season.

    So, most likely, control "on the charge lamp" is used, and the voltage at the generator output appears too early.

    The generator must work so

    Change the sensitivity of the control scheme would be meaningless, and in the 36 line signal this option is not provided. Use another method, for example, the test batch.

    If you can configure control over the generator, you can also not always, then the question arises, is it not easier to control only the voltage. Do not follow the programming of the function 11, and get this option immediately. And then try to perform the verification procedure. In almost every modern car, it will fail.

    There is a advice that does not lead in any instructions or in reviews. By connecting the "black and gray" wire to the charge lamp, try to use both options for setting - 2 or 3. If it does not help, connect to another lamp contact. But the best method, as the Starline experts themselves say is reading the engine tip signal.

    Pulses of the DVS DVS

    To implement such an option, the control cord is connected to the high-voltage tachometer terminal. You can use the output control, if we are talking about injectionboxes. Then adjust the sensitivity of the signal input, and more this operation is considered in the following chapters.

    In the function of more complex systems that do not belong to the family of the Star Line dialogue include control of the operation of the engine on the oil pressure sensor. The method perfectly works only with some engines, and low temperatures it gives failures. Use exactly the method of control that is reliable during operation in different conditions.

    Connection features, setup

    Consider the scheme that the StarLine A91 Dialog system is installed.

    Locking on the brake

    See where the voltage appears when you click on the pedal. Take into account that when you assume the error, everyone will have to be disconnected - use the coupler.

    Programming function 8 is allowed to be performed both before and after connecting the cord in the "blue" insulation.

    It remains to consider that it is necessary to program that the "pink" signal cord is correctly controlled by a cross-country. There are options responsible for the "behavior" of the StarLine A91 Dialog system during its operation. There are no such settings among them. Well, the functions responsible for autorun, also do not contain anything like this. The algorithm of the work of the manager will always be one. As we considered the necessary experts old line.

    In fact, it is better to check whether the cord is connected correctly in purple-orange isolation. When operating the autorun, you need to activate the "handler", and the specified wire reads the signal just from the brake microcopters.

    Connect the crossover will be easy. But the Instructions of the Star Line does not say the following:

    1. Despite the dialogue regime, it is easier to sobally a car with a correctly installed by the crawl than without it;
    2. The attacker will turn off the immobilizer, simply by clinging the cord on the ground, and there is no problems with hacking locks today;
    3. As soon as the autorun is implemented, due to the increased probability of hacking, the cost of CASCO will immediately increase.

    Everyone who needs autorun, with the presence of a side speaker will have to accept. Full car "guard" is too primitive to understand commands from external devices. So you have to connect bypass, in the absence of which the remote or automatic launch does not work.

    Ignition Castle Locks

    We wish you success.

    Setting the alarm from zero

    To change the values ​​of the functions listed in Chapter 1, you need to perform the following:

    1. Let the automotive security system be in "removed from protection" mode. Ignition should be turned off, and then 6 times press the Valet service button. In each system of Ultra Star, this element is present.
    2. Turn on the ignition without running the engine. 6 siren signals should be sounded if the latter was connected. Usually during operation, siren is turned off.
    3. Change the number of the option is customizable at the moment, can be single-click on the button.

    To exit the programming mode, you need to turn off the ignition or do nothing more than 9 seconds. Change the value of the function by pressing the key fob key. For the StarLine A91 signal Dialog, the instruction is fully suited, and there are no differences for the twnet version.

    Note: You can configure the start, but not shutting down the operating engine by temperature.

    The main key chain STARLINE A91 looks like this:

    Basic Signal Base Set

    To set a value equal to 4th, button 1 is pressed for a long time, and then briefly. When operating, this option is also used - it allows you to enable protection without a sound signal. For STARLINE TWAGE A91 systems, there will be no fundamental differences: there the keychain is also endowed with three buttons. Reset settings are performed as follows:

    1. Instead of 6 pressures use 10;
    2. After 10 audible signals, the VALET button is pressed;
    3. After a single short-term "bipa", you pick the key 1 on the keychain.

    If the control is used by the touchscreen, configure the sensitivity of the programmable input. The procedure is called "learning", the truth is not used in the instructions.

    You can only view the values ​​of each function on the disclosure of the keyfoot that runs in the dialog mode. It will not be necessary to change these values.

    Teach the STARLINE A91 Dialog signaling to recognize idle turns in reality is not easy. You must first turn off the "yellow" wire connected to the "15" terminal, and before the start of operation, everyone is returned to the same mind. When the cord is disabled, perform actions:

    1. Close the doors, hood, trunk;
    2. "The handbrake" deactivate;
    3. Perform the engine launch;
    4. The motor should work at idle;
    5. Sensitivity will be configured automatically.

    The StarLine A91 Dialog system is also provided with the VALET button, and the LED indicator. If learning is successful, the diode flashes. In any review, of course, do not talk about the difficulties considered here. And the instruction contains the following short text.

    Screenshot of installation manual

    What you need to know the owner

    Starline A91 Dialog alarm can be configured both on the table and the cursor method. Configuring autorun on temperature, go to the "Thermometer" symbol, but if the sensor is faulty, the icon is not activated.

    Screenshot of the leadership of ultrastar

    Such functions could not be implemented if the dialogue mode was not used. In each review, where the Security Complex Starline A91 Dialog is considered, praise and resistance to hacking. All of these characteristics, as can be understood, are related to the presence of a dialogue mode.

    There is a review, where the range of communication with the keychain was measured during testing. When operating, it is obviously several other values ​​other than "passport" are obtained. For the STARLINE A91 Dialog signaling, the following results were obtained:

    Test of communication range

    The command filed by the system from the key fob was just started starter. Characteristics here look good, but to several kilometers specified in the documentation, they obviously do not reach.

    In responses published by the owners, report information inaccessible in any review:

    • Using the mode dialog entails and negative consequences - the battery is quickly discharged in the display with the display. This effect itself is stronger at low air temperature.
    • The automotive security system of the model under consideration has its own specific disadvantages. After several seasons of operation, for example, you have to configure the shock sensor, turn it off or replace it new.
    • Automotive temperature can be used. But the thermal sensor is better to fasten under the torpedo, and not on the engine crankcase.

    Information from the list may refer to the StarLine A91 Dialog signaling, but not only to it. Ultimately, its processor program provides 3 autorun modes: in temperature, and at certain times (alarm clock) or by timer. Combined mode can be used too. Select the choice for the future owner.

    Keychain A91, its options

    A source: https://autolocked.ru/avtosignalizacii/starline-a91-dialog

    How to configure STARLINE A91 alarm autorun by engine temperature

    How to change the start of the engine starts Starline A91

    The functions of automotive security complexes include the mode of remote or automatic start of the power unit, allowing to warm the motor in the winter. Autorun Starline A91 Allows you to turn on the engine depending on the ambient temperature or at a specified time. The user activates the service and adjusts the mode of operation using the remote control.

    How to turn on autorun

    The autorun enabling implies the pre-installation of the temperature sensor, which is installed on the engine cylinder block or on the coolant supply highways. A contact is used to switch the sensor, equipped with an orange-black insulation cable (part of the 18-pin block of the alarm processor block). To ensure the operation of the automatic power on function, you need to configure the equipment.

    The design of the 18-pin connector is provided with a loop cable equipped with a black insulator. When installing the product on a car equipped with a manual transmission, you need to break the chain.

    On machines with automatic transmission, you must save the circuit in a closed state. The automatic start algorithm provides 4 scrolling of the shaft starter, the adjustment of the number of starts is not provided.

    Each subsequent start attempt is distinguished by an increase in the operation time of the starter (by 0.2 seconds).

    How to program

    To change the parameters, find the settings button and click on it, and then turn on the ignition. The system will give 6 signal signals, confirming the readiness for programming. Configure the autorun alarm STARLINE can be in accordance with the setup tables shown in the instructions.

    To select a function, use the impact on the hidden setting key (from 1 to 12 times). Then the owner presses the buttons located on the remote control, selecting the desired mode value (for example, the threshold value of the temperature or the time of operation of the engine for the warming cycle). After that, the user includes an alarm time of the starter, depending on the type of engine and its technical condition.

    When using an automatic start-up on a diesel engine, it is necessary to provide a delay between the inclusion of electrical circuits and the activation of the starter. The time interval is required to warm up the incandescent candles located in the head of the block. Heated metal elements increase the air temperature, facilitating the startup procedure. The complex allows you to select time from values ​​5, 10 and 20 seconds. Basic delay 2 seconds is designed for gasoline engine.

    It is then configured to control the operation of the power unit necessary for the timely disconnection of the starter. The design of the security complex allows you to determine the operation of the power plant by the voltage value in the on-board network, by the presence of a signal in a positive or negative generator chain and by signal transmitted by the tachometer.

    Additionally, the ignition support function is adjusted, ensuring the safe operation of the engine in the absence of the owner in the cabin.

    If the car is equipped with a special button for starting and stopping the engine, it is necessary to adjust the power output algorithm (signal on the blue cable, coming from the 6-pin harness).

    The final programming and the choice of the automatic power on the engine is performed by 3 buttons on the remote control, which are designated by the lock icons (with a fastened and open handage) and an asterisk.

    Before installing an automatic start, you should go through the system neutral installation cycle (you need for machines with manual gearbox).

    After configuration, you must check the correctness of the starting system. To test, you need to turn on the ignition, and then click on the button with the star icon. The screen includes a key icon (on the background of the windshield).

    An additional test is carried out when the engine is running: after pressing the same key, the display is additionally displayed on the display, simulating the exhaust flow.

    In the absence of icons or displaying other icons, you must check the security complex setting (in accordance with the instructions).

    Autostat for engine temperature

    Adjusting the alarm Starline to start the engine at a temperature involves setting up the central unit on the temperature threshold value. The parameter is selected from the row -5 °, -10 °, -18 ° and -25 ° C. When the sensor is cooled below the programmed value, the crankshaft is scrolled by the starter and the warming of the aggregate. To start it is allowed to use the sensor located in the engine compartment and the sensor located in the car.

    The minimum time interval between repeated launches is 1 hour. The time spent on the heating of the motor is not taken into account. The user cannot change the repeat frequency, since the parameter is determined by external temperature conditions. Installation of autorun on temperature does not provide restrictions on the number of repeated heating (depends only on the resource of the car battery).

    To activate the service, you will need to press the key marked with an asterisk. After serving the melodies and series of 3 short beeps, the programming method cursory is included.

    The user moves the cursor with short-influences to the button with an asterisk, after selecting the icon with the thermometer icon, you need to change the function value. To activate, you need to press the key with a locked lock symbol.

    When the start-up on temperature is activated by parallel modes (for alarm clock or timer).

    The keychain will give a melodic signal, accompanied by an outbreak of alarm lamps or dimensions (depends on the method of installing a security complex). On the control panel screen, the active function icon is displayed and the threshold temperature value is shown briefly, in which an attempt is made to start the power unit. The control diode alarm will flash the series consisting of 3 short flashes, confirming the readiness of the system.

    If the further use of the function is not assumed, you need to disable the service. To configure, you will need to enter the adjustment menu, select the cursor using the active icon, and then press the key marked with a lock with an open hand. The car will work 2 times the lights of the alarm, the key ring will lose the melody, which confirms the abolition of automatic warming of the motor.

    True autorun

    Before programming the engine start on timer, you must set the repetition time (from the row 2, 3, 4 or 24 hours). The function is configured through the programming menu of the StarLine A91 signaling processor. The timer autorun is activated through the menu, to enter the settings, you will need to press and hold the button with the icon. The cursor is then translated into the icon with a rotating impeller, pressing the button with the closed lock allows you to enable the function.

    The control diode installed in the car goes into operation of a series of 2 short signals. The motor starts and warms up, the subsequent starts are executed in accordance with the programmed repeat time. The function is turned off through the on-screen menu, after selecting the active icon, you should briefly press the open lock key. Feeding a melodic signal and dual alarm response confirms the cancellation of the program.

    Alarm autorun.

    Before activating autorun an alarm clinic, the user needs to set the current time on the control panel. To adjust, you need to press the button marked with an asterisk, and hold to the melodic signal and the series of 3 short sounds. After the clock field on the display begins to flash, the user adjusts the value (buttons marked by the pictograms of the locked and open lock). To go to setting the minutes, you should briefly press the key with an asterisk.

    To adjust the alarm on the key chain, it is required immediately after setting the clock again to press the button with an asterisk. To configure the inclusion time, the same buttons apply, click on which should be briefly.

    Prolonged impact allows you to set the value in accelerated mode. The user then presses the button with an asterisk once again and adjusts the minutes.

    To start the alarm clock, you will need to once again press the button with an asterisk and select the "Enabled" parameter.

    Then it is necessary to press the key to the key with an asterisk (until the length of the long and short signal). Shortly pressing the button should set the cursor on the functions of the alarm clock.

    To confirm the selection, a button with a closed lock icon is pressed. Emergency light alarm will work, the console buzzer will give 2 short beeps and will lose the melody.

    The design of the security complex does not allow simultaneous use of an automatic start-up of alarm clock and timer.

    The icon of the active function will be highlighted with dark color (together with an active alarm icon), an additional time for a few seconds is displayed for a few seconds.

    The autorun function in time does not require the location of the control in the signal reception area. The programmable service is one-time, after turning on and warm up the power unit, the mode is turned off. To re-launch, it will be necessary to conduct a new adjustment in accordance with the algorithm outlined above.

    How to increase autorun time

    The user can extend the operation of the power unit only subject to the location of the control panel at the signal reception distance.

    To add time, you will need to click on a 2-3 second button marked with a locked lock icon, and then briefly affect the key with an asterisk. The help console bundle will give a melodic signal, light alarm lamps on the car will work 1 time.

    Each impact on the keys allows you to increase the warm-up time for 5 minutes; The remaining value is briefly displayed on the display.

    If the user has raised heating, but then decided not to use the car, you can use the power off function at a distance.

    To join the engine, you will need to long press the button with the open lock symbol, and then briefly affect the key with the star icon. On the car 4 times the external light alarm will work, the power unit will turn off.

    The remote display turns out the control indicators that signal the engine warming up, and then the buzzer will fulfill the musical melody.

    Sensitivity sensitivity sensitivity

    The security complex includes a sensor that determines the strength of the strike applied by the body. The sensor is used to turn on the alarm mode, perceiving the blow as an attempt to unauthorized access to the interior of the car. The device is mounted inside the vehicle cabin, the instruction manual recommends placing the product open to adjust the sensitivity. On the case there are control diodes, which are included when fixing the strike of the car body.

    Vibrations occurring during the operation of the engine are perceived by the sensor as a hacking attempt, which leads to the triggering of the siren. To configure sensitivity, 2 potentiometers (warning zone and alarm level) are used that rotate the screwdriver sting. The regulator has 10 positions, when delivered from the factory, it is set to position 4 or 5. Before the start, it is necessary to reduce the sensitivity of the device, turning the regulators to a minimum.

    Then begin to establish a warning level. To adjust, you need to open the car door, activate the security mode, and then rotate the screw of the regulator clockwise. Sensitivity is determined by light palm strikes that are applied on the body.

    Then the user can configure the Starline alarming level (by analogy). After the adjustment is completed, it is recommended to put the security complex on the autorun and check the sensor sensitivity during the operation of the motor and when you hit the body (paton the roof panel).

    How to disable the function

    The user can turn off the automatic start using the buttons on the control panel. It is impossible to completely disable the function, since the motor operation algorithms are laid in the software of the central unit. If there are problems with automatic startup, it is recommended to forcibly reset the alarm settings, and then program the parameters again.

    A source: https://autotuning.expert/avtosignalizatsiya/avtozapusk-starline-a91.html

    How to enable autotypers to Starline A91

    How to change the start of the engine starts Starline A91

    Many security systems have additional options and opportunities that facilitate life to their owner. For example, Starline A91 is autorun. Moreover, it can be installed on any car, including such models as a VAZ 2110 or 2114. The diagram of connecting the car alarm is quite simple and can be carried out in the garage. This will require:

    • Set of a security system;
    • a set of tools including drill, drills, screwdriver, etc.;
    • Soldering supplies: Soldering lamp, solder, tin, rosin;
    • Isol, shrink tubes and industrial hair dryer.

    The diagram is shown in the figure below.

    For remote motor start, you need to connect a special six-contact connector. In this case, the wires are connected in a certain order.

    • Red cable (+ 12V) goes to the central lock;
    • Yellow (IGN1) - cable for ignition lock;
    • Two black wires are connected to the starter (thick) and ignition lock (thin);
    • Blue and green remain not connected.

    How to make autorun with buttons

    After the correct installation of the car will be able to hold a remote launch. Additionally, a number of functions for programming will be available. Starline A91 can be configured to autorun on temperature, alarm clock, time or charge of a battery. Below is the video in which it is explained which buttons must be pressed.

    Setting the STARLINE A91 alarm on autorun time

    The security system has a function of setting the remote start time. This feature allows you to start a motor at a specified hour, as well as warm it to the arrival of the owner. If the first start attempt failed, the next time the starter time is increased by 0.2 seconds. After four unsuccessful attempts on the keychain comes the appropriate alert.

    How to set the time of autorun

    In order for the function to work correctly, you need to put the correct time on the key chain. After you need to enter the programming mode, by pressing the VALET service button in the cabin six times (when the ignition is turned off). After turning the key to the ON position, the car will publish 6 sound signals.

    Now click the service button three more times, turning into the appropriate programming mode. For each pressing the machine reacts the audio signal. After that, within ten seconds, on the keychain, you must press the desired button (the first key - each two hours, the second - three hours, the third - four hours). Confirmation of the procedure will occur independently.

    Time autorun shutdown

    If necessary, you can refuse this function. Disconnection occurs as follows:

    • long (to the second signal) button 3 is pressed;
    • The cursor moves to the fan icon;
    • Deactivation of the function is carried out by short-term pressing on the second button. In confirmation of this car, the headlights twice the headlights and emit a signal.

    Starting an engine for alarm

    You can configure your own start of the engine in the alarm clinic. To do this, you will need to first configure these parameters on the keychain itself. Press button 3 before playing a small melodic signal. After that, the clock parameter on the remote must be filled. Two more short presss allow you to go to setting the alarm settings. The desired values ​​are set by clicking on the keys 1 and 2.

    To activate the autorun function, you must consistently press the third and first key (after that the clock icon flashes, the melodious sound will sound, and the car will respond to the flash of the overall signals). Using the buttons 1 or 2, you can set the necessary parameter. Then the third button is pressed again, and after the key one (confirmation of the activation of the alarm clock). Another long pressing of the third button allows you to activate the alarm autorun mode.

    Changing the warming time to Starline A91

    Depending on the selected settings, the car can warm up 10, 20 or 30 minutes. This parameter is programmed after entering the service mode:

    • Turn off the ignition and press the VALET service button six times in the cabin;
    • turn on the ignition, listen to six sound signals from the car;
    • Two twice the VALET key is clicked;
    • The next click buttons keychain defines the warm-up time (the first key is 10 minutes, the second - 20, third - 30). Confirmation of the command is made automatically, do not press anything enough.

    How to enlarge start-up time with STARLINE A91

    It happens that the machine does not start in cold conditions, if the starter works around a second (factory settings Starline A91). In this case, you can extend the time of its work. The instruction is as follows:

    • When the ignition is turned off, you must press the Valet service button six times to go to programming mode;
    • After turning the key (ON) the car blinks six times with dimensions. Then you need to press the VALET key for nine times;
    • Pressing any button on the keychain determines the speed of the starter (the first - 0.8 seconds, the second is 1.4 sec., the third is 2.0 seconds). Long plus a short click of the first button - 3.6 seconds.

    So that the starter does not twist when the work engine must be connected gray with a red wire on the panel tachometer for automatic stop.

    Setting the alarm STARLINE A91 on autorun temperature

    • Turn off the ignition, press the VALET key six times;
    • we turn on the ignition, click Valet four times;
    • Now the first button on the key chain will set the parameter -5 degrees, the second - minus 10, the third is minus 18. Long, and then the short press of the first button is responsible for setting the parameter - 25 degrees Celsius.

    How to set autorun on the engine temperature keychain

    Now the basic parameters are set, it remains only to activate the autorun function by temperature:

    • Press a long key for a long key, up to the second melodic signal, which will play the keychain;
    • Two twice by clicking on the third button so that the cursor on the display moves to the icon with the thermometer;
    • To activate, you must click on the first key once.

    Now the car will start with the temperature owner.

    Disconnection of autorun temperature

    If the owner of the car for a long time leaves or automatic launch at a temperature is not necessary, then this function can be removed. The procedure occurs in the same way:

    • We click the third button for a long time (to the second beep);
    • Two two times click on the third key to briefly to move the cursor to the pictogram of the thermometer;
    • The second button deactivate this feature.

    Why autorun autorun does not work

    Sometimes it happens that the autorun function does not work. For example, the starter turns the engine, but it does not start. In this case, it is necessary to check the presence of gasoline in the tank, as well as the charge of the battery. In the first case, everything is clear - it is necessary to add gasoline. In the second - to charge the battery.

    A source: https://galaxys6blog.ru/kak-vkljuchit-avtoprogrev-na-starlajn-a91/

    How to enlarge (extend) or reduce engine time during autorun (remote start) on StarLine A93

    How to increase or vice versa to reduce the engine operation time with automatic and remote launches on car alarm Starline A93? Judging by the comments, this particular question most often worries the owners of this system.

    And even though I already gave answers to these questions in the comments (here and on this page) and in the material Table Programming Starline A93: Instructions for setting up using a service button and a key fob - setting up a autorun, decided to still write a separate article about how to change Starline A93 engine operation time during autorun and remote start.

    1. Changing the engine time when remote or autorun StarLine A93 from the key fob

    If the car stands with an already running engine, and it does not matter how it started - on a command from a keyfob or automatically when the programmed condition (at temperature, interval, alarm or voltage occurs) is, then in this case you can only extend the time of its operation.

    To do this, you need to push the first (red) button to the second signal for a long time (second), that is, to do the same steps as when the car is remotely started the car. Engine operation time will increase by five minutes.

    If you have absolutely ancient StarLine A93, then to increase the engine operation, you need to press the 1 button (red), hold it down to the keychain, then omit and press the 3rd keychain button. That is, again, to do actions as when remotely start.

    2. Programming engine operation time when remote or autorun StarLine A93

    The factory value of the engine operation at startup is displayed 10 minutes. We can change it by 20 or 30. This value changes in Table 2 2 functions.

    To change the value of function 2, do the following:

    • 1. Press the service button 5 times when the ignition is turned off. In the latest versions of A93, this button is located directly on the antenna. For service to the antennounces of old versions, it is somewhere hidden in the car. The servers button will be accompanied by a flashing of the LED.
    • 2. Turn the ignition. It will sound 5 sirens signals.
    • 3. Briefly press 3. The key chain will display the inscription SF. You entered the programming table 2, where the functions affecting the automatic and remote launch occurs.
    • 4. Now press Long 3 to the keychain signal and then again briefly 3. The keychain's melodious signal will follow and the first function will appear on the display.
    • 5. Short press keys 2 and 3 choose the function you need 2. The key chain should be displayed the value of the function 2: 2-1 (if the operating time is set 10 minutes), 2-2 (if 20), 2-3 (30) or 2 -four.
    • 6. Short presses of the button 1, select the value of the engine operation required by us:
      1. 2-1 - 10 minutes
      2. 2-2 - 20 minutes
      3. 2-3 - 30 minutes
    • 7. Turn off the ignition.

    3. How to enlarge the engine time during autorun Starline A93 A39

    Starline - new articles

    A source: https://12voltnews.ru/starline/12-vremya-raboty-dvigatelya-starlajn-a93.

    How to set up autorun time STARLINE A91

    Maybe someone considers that this process was not worth a separate post, but because At least I set up these watches once every 5-6 months - depending on the time of resurrection of the battery, much more fun to open the blog and refresh in memory, than to google again or somehow decide.

    How to set up and set time on the STARLINE A91 key chain

    Setting time is as follows:

    You must press and hold the button under No. 3, which is designed to adjust the readings of the clock. It is necessary to hold it until one melodic signal is heard, then one short, and after two of the same short signals. After such action Starts flashing icon with clock .

    Button number 1 increases the readings of the clock, and button number 2, they are reduced accordingly;

    After that, you need to briefly press the button number 3 to set minutes. As a result of such actions, the icon with moments be blinking. Again the first button increases the readings, and the second is reduced;

    Again, you need to press a third button again, setting the alarm readings will be started. When the icon is shimging with the alarm clock, again the first button can be increased, and the second reduce the readings; Again, briefly press the same button to set the alarm minutes. Also, the buttons are the same and two increase and reduce the readings;

    The next short-term pressing of the third button will enable or disconnect the alarm. The first button can be turned on, and the second to turn it off;

    If you continue to continue to press the third button briefly, the timer reading mode is called. After the timer clock icon is blown, the same buttons increase or reduce the readings; Another brief press of the third button will flash the timer minutes icon. They are corrected by the same buttons one and two; Further pressing the three button will turn on or disconnect the timer. The first button can be turned off, and the second button is turned on back.

    As I said - there is nothing difficult in the setup (if you know where to put in your finger), but let this infea stay))

    Many security systems have additional options and opportunities that facilitate life to their owner. For example, Starline A91 is autorun. Moreover, it can be installed on any car, including such models as a VAZ 2110 or 2114. The diagram of connecting the car alarm is quite simple and can be carried out in the garage. This will require:

    • Set of a security system;
    • a set of tools including drill, drills, screwdriver, etc.;
    • Soldering supplies: Soldering lamp, solder, tin, rosin;
    • Isol, shrink tubes and industrial hair dryer.

    The diagram is shown in the figure below.

    For remote motor start, you need to connect a special six-contact connector. In this case, the wires are connected in a certain order.

    • Red cable (+ 12V) goes to the central lock;
    • Yellow (IGN1) - cable for ignition lock;
    • Two black wires are connected to the starter (thick) and ignition lock (thin);
    • Blue and green remain not connected.

    Automotive temperature Starline A91

    Many security systems have additional options and opportunities that facilitate life to their owner. For example, Starline A91 is autorun. Moreover, it can be installed on any car, including such models as a VAZ 2110 or 2114. The diagram of connecting the car alarm is quite simple and can be carried out in the garage. This will require:

    • Set of a security system;
    • a set of tools including drill, drills, screwdriver, etc.;
    • Soldering supplies: Soldering lamp, solder, tin, rosin;
    • Isol, shrink tubes and industrial hair dryer.

    The diagram is shown in the figure below.

    For remote motor start, you need to connect a special six-contact connector. In this case, the wires are connected in a certain order.

    • Red cable (+ 12V) goes to the central lock;
    • Yellow (IGN1) - cable for ignition lock;
    • Two black wires are connected to the starter (thick) and ignition lock (thin);
    • Blue and green remain not connected.

    How to set up alarm STLINLE A91

    Modern car alarms perform not only the functions of security systems. The owner of a car equipped with alarm alarm A91 has the ability to start the motor remotely using the remote control, set the necessary requirements for warming up the auto (by hours, alarm clock or temperature) by pressing certain buttons, as well as configure the turbotimer parameters. This article is devoted to the characteristics of the STARLINE keychain, as well as a detailed video with the instruction.

    How to install StarLine A91 alarm

    This security system is relatively simple in terms of operation, so its installation can be carried out with their own hands. In order to set auto alarm on the car, it will be necessary:

    • a set of tools, including screwdrivers, horn keys, etc.;
    • New Alarm Starline A91;
    • Activator driver's door;
    • Soldering supplies: lamp, tin, rosin;
    • insulating tape, shrink tubes;
    • Additional protective diode and door terminals.

    If you need to install the system on the prior, then you need to act as follows (the instruction is also relevant for other models of the car):

    • We dismantle the facing of the steering wheel;
    • unscrew the screws of the fastening of the tidy;
    • Mount the LED on the windshield, the shock sensor is on the beam, and the VALET service button is in a convenient, but hidden place;
    • We connect the 18-pin connector of the central block in accordance with the instructions and manufacturer schemes;
    • We connect a 6-pin connector to control autorun functions;
    • We carry out the connection of the central lock;
    • Connect door terminals.

    Connecting a keychain to alarm

    After the signaling is set, you must bind one or several remotes to it. To do this, you will need to know where the Valet button is located. If the installation of the car alarm Starline A91 took place, then the owner knows about its location. If the installation was done in the service center, then you need to check the following places:

    • glove box;
    • Pockets for small things in doorways;
    • space around the steering column;
    • place near the pedal node;
    • Check the central tunnel between the seats;
    • View under the decorative front panel lid in place near the fuse block.

    After that, you can proceed to the main procedure.

    How to register the main keychain

    Startline A91 alarm has one main remote control with three buttons and monochrome LCD display, which displays current functions, time, etc. Also, the keychain has feedback, so the owner can get more information about the state of the car. Bind the remote to the machine itself is simple. The procedure is carried out in a few steps:

    • When the ignition is turned off, it is necessary to press the VALET service button seven times;
    • Rotate the key to the ON position. After that, the car has been blinking with headlights seven times and emit a similar number of signals. This means that the alarm has passed into the appropriate mode;
    • Now the second and third key down to the melodic signal and one of the sirens are simultaneously pressed on the keychain;
    • Rotate the key to OFF. The successful end of the operation signals five outbreaks of the overall lights of the car.

    After that, you can proceed to programming additional functions, the table of which is presented below.

    How to register an additional keychain

    In addition to the main console, the kit includes a spare console. It is pretty small and does not have an LCD display, so many functions have to manage "blindly". But it can also be tied to alarm and program.

    • After turning off the ignition seven times press the service button;
    • Include ignition, listen to seven sirens signals;
    • Press the second and third button at the same time to bind the keychain. Basic condition - interval during binding no more than five seconds. With each successful procedure, one siren signal will be heard;
    • Turn off the ignition and wait for sound confirmation of the procedure.

    Turning on sound keychain

    The Starline A91 system refers to the category of car alarms of the average price segment. The ability to adjust or turn off the volume is missing here. If the signal disappeared, and the sound keychain is simply absent, then you need to contact the service center to eliminate this problem.

    Starline A91 Sensitivity Setup

    To prevent hacking attempts or in the event of an accident, when the car stands in the parking lot, Starline A91 alarm has a shock sensor. As a rule, the installers attach it to double-sided adhesion on the front rack of the car. Most often it is set near the driver's feet or from the front of the front panel.

    Sometimes it is necessary to reduce or increase the level of sensitivity. This will require a sensor itself, and after turning the regulators in the desired direction: clockwise to increase sensitivity and counterclockwise - to reduce.

    At the same time, the warning level is first configured. It is important that the doors are open, and the security mode is enabled.

    The second is configured to the alarming level - the procedure in this case is carried out in a similar way, but the second regulator is spinning.

    Timer Installation

    Modern Starline A91 system has a turbotimer function. This option allows the owner of the turbocharged car to leave the car by taking the ignition key with it. In this case, the turbine continues to work until its cooling. This is useful in terms of the durability of this unit. Setting this feature is carried out as follows:

    • Turn off the ignition, 6 times press the VALET service button;
    • turn on the ignition, listen 6 signals;
    • Press the service key again;
    • Now any press of the button keychain determines the duration of the turbine. The first button is 1 minute, the second is two and third - three. Prolonged pressing of the first button, and then another short click - four minutes.
    • Off the ignition confirms the specified parameters.

    Now you can activate this option. Press the third button to two beeps. After that, the turbine icon flashes on the screen. Short pressing on the first key activate this mode. Click once again the third key (before the signal) to confirm the activation.

    Setting up autotyper

    The security system has a function of setting the remote start time. This feature allows you to start a motor at a specified hour, as well as to warm it up to the arrival of the owner. If the first start attempt failed, the next time the starter time is increased by 0.2 seconds.

    After four unsuccessful attempts on the keychain comes the appropriate alert.

    To work correctly, it is necessary to put the correct time on the keychain. After you need to enter the programming mode, by pressing the VALET service button in the cabin six times (when the ignition is turned off).

    After turning the key to the ON position, the car will publish 6 sound signals.

    Now click the button three more times, moving to the appropriate programming mode. For each pressing the machine reacts the audio signal. After that, within ten seconds, on the keychain, you must press the desired button (the first key - every two hours, the second - three hours, the third - four hours). Confirmation of the procedure will occur independently.

    To turn it on, it is necessary to push the third button until the second melodic signal. After that, the left icon on the panel flies. Another press of the button three moves the cursor to the fan icon, and the short press press confirms the choice.

    Enable engine temperature

    More relevant during the cold period is the automatic launch of the engine temperature. Unlike the previous way, the engine will not start, if it is warm and there is no need to warm it. This option is programmed as follows:

    • Turn off the ignition, press the VALET key six times;
    • Include ignition, listen to six sound signals, click VALET four times;
    • Now the first button on the console will set the parameter -5 degrees, the second is minus 10, the third is minus 18. Long, and then the short press of the first button is responsible for setting the parameter - 25 degrees Celsius.

    Setting the duration of the starter scroll

    It happens that the machine does not start in cold conditions, if the starter works around a second (factory settings Starline A91). In this case, you can extend the time of its work. The instruction is as follows:

    • When the ignition is turned off, you must press the Valet service button six times to go to programming mode;
    • After turning the key (ON) the car blinks six times with dimensions. Then you need to press the VALET key for nine times;
    • Pressing any button on the keychain determines the speed of the starter (the first - 0.8 seconds, the second is 1.4 sec., the third is 2.0 seconds). Long plus a short click of the first button - 3.6 seconds.

    So that the starter does not twist when the work engine must be connected gray with a red wire on the panel tachometer for automatic stop.

    Configuring a closer

    Optionally, Starline A91 alarm can be equipped with closer of glasses. When installing, you need to connect to the electric drive glass. After that, they will independently close after the placement of the machine under protection. This feature is optional and can be installed in a specialized service center.

    How to set the key chain

    In order to avoid accidental presses in your pocket and activate unnecessary functions, there is a shutdown option or blocking STARLINE A91. To do this, you must simultaneously click on the first and third button. Unlock occurs in the case of simultaneously pressing the second and third key.

    Reset

    If you have different problems or luggles of car alarm, it is recommended to reset the settings to the factory parameters. To throw them, it is necessary to carry out the following procedure:

    • The ignition key is inserted into the lock and rotates to the ON position;
    • After that, pressing the rnet service key is 10 times;
    • Now you need to turn the key to the OFF position. Machine Ten times blinking with dimensions, as well as emit ten sound signals, confirming the successful transition to the user setting reset mode;
    • Once again, press the VALET button again, and the car once again issues a signal;
    • The first button is now pressed on the keychain. A short melody will confirm that the operation is successful, and all parameters are returned to factory;
    • To end the procedure, you need to turn the key to the ON position. The second way is not to press anything for ten seconds. The fact that the exit is carried out will report the car itself, which blinking with dimensions. The keychain will play a short melody.

    How to set up a key chain after replacing the battery

    After replacing the supply element in the STARLINE A91 keychain, the clock is knocked on the factory parameter (00-00). Accordingly, the start of the motor and other functions are incorrect. Therefore, it is required to re-adjust the clock:

    • Click and hold the three to the third beep. Now the clock indicator flashes on the display.
    • With the first and second keys, we increase or decrease this indicator;
    • The next click on the third key transfers to setting minutes. It is carried out in the same way (keys one and two);
    • Next follows the configuration of the alarm, as well as setting time for the timer;
    • To confirm the parameters, not to click anything for a few seconds.

    Next, you should restore the remaining parameters set by the user.

    Alarm Operation Manual Starline A91

    For a complete understanding, how custom settings are made, it is necessary to study the operation manual and the Starline A91 programming table. The reference to the document is placed below.

    Material author: Borisov Maxim

    A source: https://rus-avtomir.ru/beep/starline/nastrojka-brelka-a91

    STARLINE A91 Alarm - Features, Management, Setup - About Auto

    In connection with the active growth of statistics on theft of vehicles, more and more drivers began to think about buying a security system.

    However, due to the wide abundance of manufacturers and models, choose the most suitable option is not as simple as it seems.

    Well, to solve this problem, we recommend paying your attention to the STLINLE A91 alarm with auto-site (key fob's instruction, price and photo), which is a high-quality new product in its segment.

    Equipment and signaling characteristics Starline A91 with auto start

    Buying the alarm STARLINE A91 (the price of the device varies within 3500-4000 rubles), the motorist receives a whole set of additional equipment, which includes:

    • Installation and safety instructions;
    • Two branded key rings (main, with LCD screen and spare);
    • Replaceable battery;
    • Control module;
    • Antenna;
    • Shock sensor;
    • A regular case;
    • A set of wires for connecting accessories (how to connect alarm to a car, we will look at the article below);
    • Sensor for boobspace;
    • Temperature meter;
    • The service key (where is the rnet button on the STARLINE A91 alarm and how to use it, we will tell in the detailed instructions below).

    After installing the listed components on your car, the owner can use the presented device not only as sound or silent protection, but also for:

    • Control of the central locking;
    • Warming up the motor and the salon (how to set the time of automatic engine start and specify the necessary heating temperature, we will find out a little later);
    • Immobilizer settings.

    At the same time, the device is able to catch the signal from the key fob in 4 channels, at a distance of 700 to 1500 meters away. And for its power it is enough 25 mAh, which can be obtained from a 12-volt battery.

    Setting the key fob and buttons designation

    On the block chassal from the STARLINE A91 alarm, there are three main buttons responsible for setting up the entire security system. Well, how to activate with their help the desired option, see the table below:

    Button number With single press With long retention With double pressed
    1 Turning on the alarm, followed by locking doors Silent car setting Activation of the shock sensor
    2 Removing the car with alarm, followed by unlocking doors Silent destruction Deactivation of damage sensor
    3 Checking the current state of the security system and the temperature regime in the auto cabin Select engine start mode: by timer, temperature, or alarm Activating motor automatic warming mode
    "Valts" Alarm emergency reset (turns off Siren, and unlocks the car)

    It is worth noting that the "Valts" button is located not on the keychain itself, but in the cabin of the car, so that it is not noticeable.

    But when the battery is discharged, or open the door with the key (without prior to reset the alarm from the keychain), it becomes the only salvation for the car owner.

    After all, when it is pressed, the security system automatically goes into service mode, which gives the driver the opportunity to get to the house, or to the nearest one hundred.

    In addition to the above options, the instruction manual for the alarm STARLINE A91 also provides additional functionality that is activated when a combination of two buttons:

    • 1 and 2 keys (sequentially) - activation of silent alarm;
    • 1 and 3 keys (alternately) - manual start of the motor (with an already operating internal combination of these two buttons extends the set timer twice);
    • 3 and 2 keys (sequentially) - inclusion of the second channel;
    • 1 and 3 keys (at the same time) - block blocking;
    • 2 and 3 keys (at the same time) - removal of blocking.

    How to bind the keychain to the alarm Starline A91 after installing on the car, we will look at the article below.

    Hidden security system with keychain

    How to disable the alarm STARLINE A91 buttons of the currency and with what combination of the keys to run the motor, we have already found out. But before giving teams to the device, it needs to be tied to the branded bracer. And this is done as follows:

    1. The ignition key is inserted into the lock, and scrolls until the position is "enabled" (characteristic indicators should light up on the dashboard);
    2. When the ignition is turned on, the "Valts" key is successively seven times;
    3. The key in the lock turns twice, in different directions, to first turn off completely, and then turn on the ignition again (when the dashboard is re-turned on, the alarm must submit 7 short beeps);
    4. After the seventh signal sounds, the keys 2 and 3 will be pressed on the key chain at the same time (it is necessary to keep them until the security system will not publish a characteristic sound);
    5. Turn off the ignition and turn on it again. If the car gives a light signal for 5 times, this means that the blocking of the block is completed and the subsequent combinations of its buttons will be directly controlled by the device.

    The same handling instruction, in a pair with the STARLINE A91 alarm circuit with autorun, must be present in the list of component elements of the device.

    A source: https://avtokaster.ru/remont/signalizatsiya-starline-a91-osobennosti-upravlenie-nastrojka.html.

    Auto start to Starline A91, which buttons click to make the car from the key fob

    Despite the fact that Starline A91 alarms from the class of budget models of security systems, it meets all the requirements of protection of this kind of devices. It has a data stream of 8 floating channels with a 128-bit encryption code with an intelligent autorun function. This complicates the interception of the signal, since the system itself, with each "keychain-car" dialogue, automatically selects the radio frequency that in urban conditions with radio cells has an important meaning.

    How to start the car from the block

    It is known that the STARLINE A91 security system has a motor autorun. But before this it is necessary to perform a number of mandatory actions:

    1. Transfer the PPC knob to the neutral position (turn off all transmissions);
    2. Turn off the ignition and pull out the key from it (the engine must be included);
    3. Activate parking brake.
    4. Tightly slam all the doors, as well as the hood and lid of the trunk;

    If some stage is missing, the remote start is not possible. But with proper preparation of the machine (the motor is dried by the warning itself), it can be started with a remote option.

    1. Press and hold three seconds button number 1 and after the audio signal quickly press the button number 3:
    2. Or periodic engine start from keychain:

    This feature is especially relevant in the winter when periodic engine heating is required. The StarLine A91 key chain can automatically run the engine for heating (after 2, 3, 4, 24 hours).

    How to set up autorun time, temperature

    Starline A91 Dialog Alarm is allowed to configure this manner that it will automatically start the engine at air temperature (usually minus) or after a specific time interval.

    Activate the autorun mode for temperature

    This function will work when complying with certain conditions:

    • in the presence of a temperature sensor;
    • from the place of its installation;
    • Feed the sensor itself.

    It is activated by long pressing the button 3 (asterisk) until the sound signal appears from the key fob - it should be fun once. The display will be blinking the extremely left icon (1) at the bottom of the screen. Short presses on the 3 button moving around the menu to the third left position (square 3) with a thermometer symbol.

    After you were convinced that the desired function is activated, press the button number 1 on the housing to activate this mode (this mode is turned off by pressing the button 2 on the housing), and at the point of readings of the clock, the critical value of the motor temperature after which its autorun will appear.

    After the temperature value was highlighted, it is not necessary to feed anything - after 8-10 seconds, the remote key itself is picked and the clock will again appear on the display, and the third icon (with a thermometer) will remain dark. According to this icon, it shows whether the autorun mode is started at a temperature: dark - mode is active, light - reset.

    Time autorun

    To enable this feature, you need to select the display icon 2 on the display. The machine is blinking by the headlights, and the melodic signal will be distributed on the keychain. Now through the time set by the owner, the signaling itself will periodically launch the engine.

    If, after the first attempt, the car did not start, the second will follow. At the same time, the starter scroll time will be increased by 0.2 seconds. The timer is designed for 4 attempts to start the engine. If, after the fourth attempt, the engine did not start, triggered a beep on the key chain. To configure the engine warming in time, the sequence of actions is:

    • Press and holds a long button number 3 on a key chain (asterisk).
    • The keychain will briefly picnet, but the button is pressed, after the second audio signal, release the button;
    • Fits the extreme left icon (1) on the panel;
    • Shortly pressing button number 3, move to the fan icon;
    • One short press of the button number 1 - the keychain will play melody;
    • To wait ten seconds until the key chain is spinning, and the icon with the fan will remain darkened;
    • The interval function is activated.

    It turns off in the same way, but the choice is confirmed by the # 2 button (open lock) When the engine is successful, the exhaust gases appears on the screen. The car itself is 3 times blocked by the headlights and give a beep three times.

    The reasons for which autorun does not work and how to eliminate them

    Autostart from the StarLine A91 console may well break through the operation. Most often, the reason should be sought not in outdated details, but in improper operation of the system or its installation. If autorun does not work, there may also be problems with incorrect software configuration.

    The most frequent prerequisites for breakdowns

    • The shock sensor does not work. A migration of the shock sensor itself can help.
    • Too frequent alarm operation. There are probable reasons for two. Or too sensitive settings, or corrosion on the connections.
    • No response from keychain commands. If there is no response from the machine to the commands supplied from the control keychain - the controls of the control button or the village of the battery. It may be necessary to fully replace the key chain with a new propelle in the system.
    • Doors of the machine are not closed off the console. Master in service centers can help to cope with the problem. It is necessary to check and determine which places of breaks in the chains between the main unit and the door, compliance with the technical requirements of the actuators and how the door closing pulse is programmed.
    • Autostart stopped working. Most often, the reason lies in a faulty wiring. It may be damaged. The immobilizer commander is also incorrectly delivered (most likely the antenna itself). You must also check the device programming.
    • Car siren does not work. Feed or siren itself, or there was a break in the wiring. Eliminate the problem will help the full replacement of the siren itself or the monitoring of the wiring of the entire system.

    A source: https://alarmspec.ru/signalizaci/starline/a91-avtozapusk.html

    As you know, I live alarm STARLINE A 91 dialogue, which showed itself from a decent side and in winter and summer. There was really the moment that the car did not start in -30 in no morning and did not want to sit in the evening))), I had to go to the nearest underground heat parking, where to spend the night and worry. So before that, the automatic start of the engine was carried out at a temperature - 25 seconds, however, as practice has shown at - 25 cars may simply get started. Therefore, it was decided, raise the start temperature to -18. For what is necessary when the ignition is turned off, press 6 times on the software button

    Software button included

    Soft button

    After that turn on the ignition, it will sound 6 audio signals, then press the program button again 4 times, which corresponds to the programmable function No. 04 - automatic start of the engine at the temperature,

    List of programmable functions Table 2

    After that, press the 3 button on the keychain (with an asterisk image). On the keychain will appear 4_3, then you need to turn off the ignition. Programming is completed, rejoice and dance)))

    List of programmable functions Table 1 To change which you want to press the program button 5 times

    Continuation of the list of programmable functions of the table 1

    Do not forget to put "Like" Thank you all, all good!

    Добавить комментарий